Page 1 of 4 123 ... LastLast
Threads 1 to 20 of 61

Forum: CR-10

A place to discuss CreationReality 3D Printers. Specially the CR-10 model but not limited to it. All clones/rebrandings are welcome too!

  1. Question Bed heater problem

    Started by Fester, 12-14-2018 12:48 AM
    bed heater, heater, wire harness
    • Replies: 1
    • Views: 22
    12-14-2018, 04:23 AM Go to last post
  2. Heating issue

    Started by ptizeff51, 12-13-2018 05:00 PM
    • Replies: 3
    • Views: 32
    12-14-2018, 01:30 AM Go to last post
  3. Problem Cr-10 Heatbed and Nozzle not heating up

    Started by Marcel, 12-12-2018 04:11 PM
    • Replies: 1
    • Views: 47
    12-13-2018, 05:27 PM Go to last post
  4. clear plastic box

    Started by sam, 12-12-2018 02:22 PM
    • Replies: 1
    • Views: 17
    12-12-2018, 03:31 PM Go to last post
  5. CR10 display control knob intermiten

    Started by dmyers, 11-14-2018 03:49 PM
    • Replies: 4
    • Views: 540
    11-16-2018, 10:10 AM Go to last post
  6. New User Wondering about Spares

    Started by Worn, 11-15-2018 07:28 PM
    • Replies: 1
    • Views: 115
    11-16-2018, 09:38 AM Go to last post
  7. new user needs help

    Started by bobg4pen, 10-26-2018 11:16 PM
    • Replies: 3
    • Views: 338
    10-27-2018, 05:11 PM Go to last post
  8. Will this forum be useful to a CR-20 user?

    Started by Shiplake, 10-24-2018 05:49 PM
    cr-20
    • Replies: 3
    • Views: 270
    10-25-2018, 05:10 PM Go to last post
  9. Help, Hot end enclosure seeping out molten filament

    Started by n1xson, 10-15-2018 07:23 PM
    • Replies: 1
    • Views: 287
    10-16-2018, 08:38 AM Go to last post
  10. Angry HELP ME! extruder KILLED error

    Started by segurilisstudios, 10-09-2018 11:19 AM
    broken, error, extruder, killed, problem
    • Replies: 4
    • Views: 344
    10-09-2018, 08:34 PM Go to last post
  11. Print Halted Hotend shuts off while auto homing

    Started by Bryants, 10-02-2018 05:34 PM
    • Replies: 4
    • Views: 383
    10-04-2018, 06:25 PM Go to last post
  12. High pitch sqweeling noise

    Started by mouse51180, 09-26-2018 01:33 AM
    • Replies: 5
    • Views: 416
    09-30-2018, 01:44 PM Go to last post
  13. Keenovo Heat Bed

    Started by KmxSoft, 07-15-2018 08:16 PM
    • Replies: 0
    • Views: 718
    07-15-2018, 08:16 PM Go to last post
  14. Cool Creality Ender 4

    Started by titrisol, 06-08-2018 08:22 PM
    • Replies: 2
    • Views: 1,010
    06-28-2018, 01:55 PM Go to last post
  15. Question Highest nozzle and bed temps for CR10s

    Started by dbasberg, 06-18-2018 06:17 PM
    nozzle temperature
    • Replies: 5
    • Views: 982
    06-20-2018, 01:16 PM Go to last post
    • Replies: 1
    • Views: 447
    06-11-2018, 08:44 AM Go to last post
  16. Introduction, and a word of advice.

    Started by Joe1906, 05-28-2018 06:51 AM
    • Replies: 1
    • Views: 541
    05-28-2018, 05:41 PM Go to last post
  17. Angry CRS10 bed level

    Started by FRANK, 05-09-2018 01:49 PM
    • Replies: 4
    • Views: 899
    05-11-2018, 11:39 PM Go to last post
    • Replies: 2
    • Views: 697
    04-24-2018, 12:29 PM Go to last post
  18. Newbie Setup question

    Started by paulororke, 04-15-2018 10:18 AM
    • Replies: 2
    • Views: 696
    04-18-2018, 01:46 AM Go to last post

 

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •