Page 1 of 5 123 ... LastLast
Threads 1 to 20 of 99

Forum: CR-10

A place to discuss CreationReality 3D Printers. Specially the CR-10 model but not limited to it. All clones/rebrandings are welcome too!

  1. Question Cr10s s5 TH3D firmware upload issue!!

    Started by suryanibbas, 06-14-2019 07:03 PM
    • Replies: 1
    • Views: 50
    06-15-2019, 05:31 AM Go to last post
    • Replies: 0
    • Views: 44
    06-14-2019, 07:03 PM Go to last post
    • Replies: 0
    • Views: 60
    06-13-2019, 07:01 PM Go to last post
  2. CR10-S & Cura 4.1.0 problems

    Started by Woody Allan, 06-10-2019 10:59 AM
    • Replies: 0
    • Views: 82
    06-10-2019, 10:59 AM Go to last post
  3. My first try ...

    Started by keldsor, 06-09-2019 02:41 PM
    • Replies: 0
    • Views: 47
    06-09-2019, 02:41 PM Go to last post
  4. Lightbulb Cr10s faster speeds? Your forts please😊

    Started by Rikrik, 06-07-2019 12:44 AM
    cr10, dual extruder, faster
    • Replies: 1
    • Views: 45
    06-07-2019, 02:18 AM Go to last post
  5. New to this!!!!

    Started by Thomasgrnd, 05-15-2019 08:44 PM
    • Replies: 4
    • Views: 201
    05-31-2019, 10:14 PM Go to last post
  6. losing usb connection (bad mains power?)

    Started by mark-hahn, 05-30-2019 06:54 AM
    cr10, power, power loss recovery, reboot
    • Replies: 1
    • Views: 76
    05-30-2019, 02:16 PM Go to last post
  7. Should I or should I NOT buy a CR-10s PRO ?

    Started by keldsor, 05-29-2019 07:04 PM
    • Replies: 1
    • Views: 114
    05-29-2019, 08:59 PM Go to last post
    • Replies: 5
    • Views: 263
    05-23-2019, 10:09 PM Go to last post
  8. Identify the cause of this artifact.

    Started by Tfactor, 04-28-2019 01:28 AM
    2 Pages
    1 2
    • Replies: 11
    • Views: 494
    05-05-2019, 04:05 PM Go to last post
  9. CR-10s Pro bed-plate replacement?

    Started by Slivers, 04-30-2019 06:27 PM
    • Replies: 1
    • Views: 129
    04-30-2019, 06:43 PM Go to last post
  10. CR-10 How to get power loss recovery working

    Started by john p, 04-16-2019 03:18 PM
    2 Pages
    1 2
    cr-10, marlin, power loss recovery
    • Replies: 11
    • Views: 413
    04-28-2019, 04:09 PM Go to last post
  11. Question CR-10S filament sensor turns off heated bed

    Started by Brainwave82, 04-26-2019 12:37 AM
    cr10s, filament sensor
    • Replies: 2
    • Views: 160
    04-26-2019, 09:33 AM Go to last post
  12. CR10-X Printing Issues... HELP!

    Started by phantom309oo7, 04-22-2019 01:25 PM
    • Replies: 4
    • Views: 170
    04-23-2019, 08:54 AM Go to last post
  13. Can you shorten a CR-10 S5

    Started by AaronM, 04-23-2019 02:26 AM
    cr-10 shorten
    • Replies: 3
    • Views: 156
    04-23-2019, 07:56 AM Go to last post
  14. Question Problem printing cylinders

    Started by Trickle, 04-19-2019 06:23 PM
    • Replies: 5
    • Views: 224
    04-19-2019, 09:37 PM Go to last post
  15. Problem reaching higher temperatures

    Started by Grant B, 04-05-2019 01:10 AM
    • Replies: 6
    • Views: 358
    04-05-2019, 07:13 PM Go to last post
  16. Help on pause to change filament,

    Started by ZippyStar, 04-01-2019 09:15 AM
    2 Pages
    1 2
    • Replies: 11
    • Views: 596
    04-02-2019, 01:37 PM Go to last post
  17. Question Has anyone had this problem? (Stepper motor?)

    Started by Duckduck, 03-22-2019 10:50 PM
    belt, not pulling, problem, stepper motor, x axis
    • Replies: 5
    • Views: 259
    04-01-2019, 06:06 PM Go to last post

 

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •