• MegaloDon's Avatar
    02-17-2018, 11:22 PM
    MegaloDon replied to a thread Replace Cube 3 Nozzle in Cube3
    Attached is a basic model of the nozzle with push-nut built in if anyone wants to do anything with it. I included a cutaway version to make it...
    11 replies | 262 view(s)
  • MegaloDon's Avatar
    02-17-2018, 06:32 PM
    MegaloDon replied to a thread Replace Cube 3 Nozzle in Cube3
    Are you saying the hole in the end is .5 mm? I always thought it was .4 mm. That's good to know.
    11 replies | 262 view(s)
  • MegaloDon's Avatar
    02-16-2018, 03:32 AM
    MegaloDon started a thread Material Codes in Cube3
    This is a list of material codes for the BFB files set in the lines "^MaterialCodeE1:82", etc. The colors are not so important because it will let...
    0 replies | 49 view(s)
  • MegaloDon's Avatar
    02-08-2018, 05:53 AM
    MegaloDon replied to a thread .cube3 file decoder in Cube3
    That is pretty awesome! It has links to older firmware and software that nobody could seem to find before! So I decided to do some scripting and...
    12 replies | 1080 view(s)
  • MegaloDon's Avatar
    02-02-2018, 10:29 PM
    MegaloDon replied to a thread [ HOW TO ] Use other slicers with cube 3 in Cube3
    I have already done most of what you are suggesting. I have some samples I can share with you. I haven't posted anything yet until I am sure they...
    273 replies | 36363 view(s)
  • MegaloDon's Avatar
    02-01-2018, 06:13 PM
    MegaloDon replied to a thread [ HOW TO ] Use other slicers with cube 3 in Cube3
    First you have to understand that BFB is very different from GCode. The reprap wiki only has some references that apply to BFB. For example, G1 is...
    273 replies | 36363 view(s)
  • MegaloDon's Avatar
    02-01-2018, 07:05 AM
    MegaloDon replied to a thread [ HOW TO ] Use other slicers with cube 3 in Cube3
    Unfortunately, I have never experimented with turning any fans off. The M107 command does not say which fan(s) it turns off. M103 is retract. To...
    273 replies | 36363 view(s)
  • MegaloDon's Avatar
    01-30-2018, 09:42 PM
    MegaloDon replied to a thread [ HOW TO ] Use other slicers with cube 3 in Cube3
    M104 is for the left extruder and M204 is for the the right one. http://www.print3dforum.com/showthread.php/935-BFB-(G-Code)-for-Cube-3 Also PLA...
    273 replies | 36363 view(s)
  • MegaloDon's Avatar
    01-27-2018, 11:12 PM
    MegaloDon replied to a thread The M$ 3D Builder Thread in Cube3
    I had similar problems. The answer was much simpler for me. I just unplugged the USB from the printer and then uninstalled the print drivers. When...
    29 replies | 2912 view(s)
  • MegaloDon's Avatar
    01-26-2018, 07:19 AM
    It's important to note that propane heaters give off moisture while they heat. Electric heaters on the other hand give off a dry heat and are...
    94 replies | 12833 view(s)
No More Results
About bolsoncerrado

Basic Information

Statistics


Total Posts
Total Posts
2,971
Posts Per Day
2.46
General Information
Last Activity
02-22-2018 11:47 AM
Join Date
11-06-2014
Referrals
5

2 Friends

  1. MegaloDon MegaloDon is offline

    Expert 3D Printer

    MegaloDon
  2. nunyafb nunyafb is offline

    3D Printer Noob

    nunyafb
Showing Friends 1 to 2 of 2

02-21-2018


02-19-2018


02-17-2018


02-16-2018