MegaloDon
Expert 3D Printer
Find latest postsMini Statistics
- Join Date
- 01-25-2017
- Last Activity
- 06-10-2018 07:43 AM
More 3 Friends
Recent Visitors
- 3DSurfer,
- Ashena,
- bobskinner,
- breaker,
- DonaCorning,
- joecochran1980,
- KHMusicMan,
- techbeni,
- tprothma,
- ztoddman1
- Tab Content
- MegaloDon's Activity
- About Me
- Friends
- Post Thanks / Like
-
Older Activity
-
Yesterday, 09:41 PMYes, S4 and S5 take ages to heat up... It's a very large surface and the bed heater covers MOST of it but not all of it...2 replies | 15 view(s)
-
01-14-2019, 09:32 AMNo, its a driver, like A8 or DRV8825.3 replies | 76 view(s)
-
01-13-2019, 09:21 AMI think they follow the same PIN orientation as many, just match GND pins and that should be it....3 replies | 76 view(s)
-
01-11-2019, 09:26 AMActually that would have been feasible as long as PLA would have been humidity friendly lol3 replies | 78 view(s)
-
01-10-2019, 03:42 PMhttps://all3dp.com/4/polaroid-release-europe-playsmart-3d-printer/?omhide=true&utm_source=Newsletter&utm_campaign=983ff6359d-Newsletter Heheheh3 replies | 78 view(s)
-
01-08-2019, 03:11 PMhttps://www.instructables.com/id/LED-3D-Printer-Bed-Leveling-Tool1 replies | 50 view(s)
-
01-08-2019, 07:30 AMOMFG LOL ROTFL What a steal of a machine! LOL196 replies | 27420 view(s)
-
01-07-2019, 10:44 PMFor a moment I thought the CocoJet was an April's fool lol But not... https://www.slideshare.net/fernandosaenzmarrero/cocojet196 replies | 27420 view(s)
-
01-03-2019, 07:01 PMYeah but you have the issue only in one of the three arms right? Or on the three?5 replies | 154 view(s)
-
01-03-2019, 05:26 PMIt could either be a temporary clog that auto-resolved (due to bad filament or whatever) or a slicer setting that is not correctly set or the object...5 replies | 154 view(s)
-
01-03-2019, 11:22 AM1.0 is close to the risky side as the build up pressure and the slow speed in order to get the correct deposition is for experts actually.... have u...3 replies | 93 view(s)
-
12-31-2018, 11:25 AMJust, VERY carefully, grab the usb port with 2 fingers and try to wiggle it up and down... if there's even the SLIGHTEST movement, then its probably...4 replies | 163 view(s)
-
12-31-2018, 11:06 AMHave you opened the box to see if the port is still good? Many usb ports on the crealitys "unsolder" or simply "break"....4 replies | 163 view(s)
About MegaloDon
Basic Information
Statistics
Total Posts
- Total Posts
- 479
- Posts Per Day
- 0.66
General Information
- Last Activity
- 06-10-2018 07:43 AM
- Join Date
- 01-25-2017
- Referrals
- 2
3 Friends
Showing Friends 1 to 3 of 3
No results to show...