Tab Content
  • MegaloDon's Avatar
    Yesterday, 05:59 PM
    I think there is a difference in the gap between the gear and the wheel. I have had bad luck using the ABS labeled ones. I use the PLA ones for...
    2 replies | 10 view(s)
  • MegaloDon's Avatar
    Yesterday, 05:54 PM
    My first 5 or 6 print heads while testing were PLA. I never had any warping issues when printing PLA. The only warping issues I had was printing...
    29 replies | 499 view(s)
  • MegaloDon's Avatar
    Yesterday, 06:54 AM
    I got my first Txx error today when trying to print with 3D Builder. It also doesn't want to put the first layer low enough even when I set the gap...
    218 replies | 27817 view(s)
  • MegaloDon's Avatar
    08-16-2017, 07:37 AM
    I just posted a new version that has better clips, rafts, and some other minor tweaks. ...
    29 replies | 499 view(s)
  • MegaloDon's Avatar
    08-15-2017, 10:35 PM
    I wouldn't blame the Cube for this particular issue. Seems it's the filament's fault. I think any printer that uses a bowden tube would have this...
    29 replies | 499 view(s)
  • MegaloDon's Avatar
    08-15-2017, 06:26 AM
    MegaloDon replied to a thread [ HOW TO ] Cube Print Temperature Modifier *beta* in Cube3
    Mythandar, I find that my Inland ABS works better with the first layer at 260 (sticks to the build plate better) and the rest at 250. I...
    43 replies | 2073 view(s)
  • MegaloDon's Avatar
    08-15-2017, 05:05 AM
    There's no fix for this that I know of. It's not an issue with the print head. The filament is restricting in the tubing that goes from the...
    29 replies | 499 view(s)
  • MegaloDon's Avatar
    08-13-2017, 12:16 PM
    MegaloDon replied to a thread The Printing Lounge in Cube3
    It won't affect printing as long as it fits well. I was just pointing out that it would look much cleaner. If it were sticking out too much, you...
    126 replies | 7139 view(s)
  • Mythandar's Avatar
    08-12-2017, 07:09 AM
    Mythandar replied to a thread [ HOW TO ] Blob Shield in Cube3
    Figuring this out was a good catch don. I bet it still kinda does this in the other slicers, but I always had it randomize where it started the next...
    9 replies | 137 view(s)
  • Mythandar's Avatar
    08-12-2017, 06:56 AM
    Mythandar replied to a thread [ HOW TO ] Blob Shield in Cube3
    I had looked through the cubify program to see what could be modified. Unfortunately, they have all the important files encrypted. I spent a little...
    9 replies | 137 view(s)
  • MegaloDon's Avatar
    08-12-2017, 06:39 AM
    MegaloDon replied to a thread [ HOW TO ] Blob Shield in Cube3
    Then what ARE you saying???? You didn't answer ANY of my questions. Are you just trolling me? Why do you feel the need to say everything I say...
    9 replies | 137 view(s)
  • MegaloDon's Avatar
    08-12-2017, 05:17 AM
    MegaloDon replied to a thread [ HOW TO ] Blob Shield in Cube3
    I have not experienced this yet. What issues does it cause? I don't understand how that would help. The object has to be under the print...
    9 replies | 137 view(s)
  • MegaloDon's Avatar
    08-12-2017, 04:46 AM
    MegaloDon started a thread [ HOW TO ] Blob Shield in Cube3
    I'm not sure if the way that the Cube Print software causes blobbing is unique to the Cube Print software or if anyone else has come up with a...
    9 replies | 137 view(s)
  • MegaloDon's Avatar
    08-12-2017, 12:28 AM
    MegaloDon replied to a thread LCD problem! in Cube3
    No, he left out the filament stretcher. :p
    16 replies | 240 view(s)
  • Mythandar's Avatar
    08-11-2017, 08:38 PM
    Mythandar replied to a thread (Open)Cube 4 anyone? :D in Cube3
    Are you referring to the z-wobble? From what I've read, any printer that uses lead screws or threaded rods for the z axis can have that issue if the...
    13 replies | 682 view(s)
  • MegaloDon's Avatar
    08-11-2017, 06:05 PM
    If the printer is connected to WIFI and the Cube Print software is running, the software turns the printer on. Are you leaving the software running?...
    4 replies | 73 view(s)
  • MegaloDon's Avatar
    08-11-2017, 03:07 PM
    From above post: I will post this later. It is an M5 fitting. This is the only part you have to purchase (besides filament). The rest...
    29 replies | 499 view(s)
  • MegaloDon's Avatar
    08-10-2017, 06:58 PM
    Here it is >>> https://drive.google.com/open?id=0B6K745kRy16-ak4xOFZIWFJyRUk Note: This is designed to print on the Cube 3 using Cube Print...
    29 replies | 499 view(s)
  • MegaloDon's Avatar
    08-10-2017, 06:56 PM
    MegaloDon replied to a thread The Printing Lounge in Cube3
    The vertical line running from top to bottom. Normally it would cause a blob along this line which has to be removed for it to fit. The blob shield...
    126 replies | 7139 view(s)
  • MegaloDon's Avatar
    08-10-2017, 05:05 PM
    MegaloDon replied to a thread The Printing Lounge in Cube3
    I find it too restrictive.
    126 replies | 7139 view(s)
  • MegaloDon's Avatar
    08-10-2017, 03:15 PM
    MegaloDon replied to a thread The Printing Lounge in Cube3
    That's the problem. It is oriented to be printed with the left extruder. To print it with the right extruder, you need to rotate it 180 degrees so...
    126 replies | 7139 view(s)
  • MegaloDon's Avatar
    08-10-2017, 05:16 AM
    Ha, I didn't think of that! That would certainly do it. :p
    9 replies | 117 view(s)
  • Mythandar's Avatar
    08-10-2017, 05:13 AM
    You probably put the spring inside the nozzle on the wrong side. The spring goes above the round retainer thingy, not below it.
    9 replies | 117 view(s)
  • MegaloDon's Avatar
    08-10-2017, 12:36 AM
    MegaloDon replied to a thread The Printing Lounge in Cube3
    Bo is testing it right now. I will post it if he doesn't find any issues. Works fine for me so far. You'll still need the metal parts of the print...
    126 replies | 7139 view(s)
  • MegaloDon's Avatar
    08-10-2017, 12:27 AM
    That was actually me. :p TommyDee had the idea to make the adjustment and I designed it. He later redesigned it to have rounded corners.
    9 replies | 117 view(s)
  • MegaloDon's Avatar
    08-10-2017, 12:16 AM
    MegaloDon replied to a thread The Printing Lounge in Cube3
    Did you print with left or right extruder?
    126 replies | 7139 view(s)
  • MegaloDon's Avatar
    08-08-2017, 09:12 PM
    What prevents the lite version from twisting?
    65 replies | 4086 view(s)
  • Mythandar's Avatar
    08-08-2017, 05:18 AM
    Mythandar replied to a thread Purge-No print in Cube3
    When this happened to me I would say it was caused by For me, I was playing around with using other slicers and was trying to do a print that used...
    48 replies | 788 view(s)
  • MegaloDon's Avatar
    08-08-2017, 04:53 AM
    MegaloDon replied to a thread Purge-No print in Cube3
    If it were a bad wire connection, it wouldn't purge properly either. Sounds more like a firmware issue. Or possibly even the Cube Print software. ...
    48 replies | 788 view(s)
  • Mythandar's Avatar
    08-07-2017, 12:12 AM
    Mythandar replied to a thread Purge-No print in Cube3
    I've seen this before. It only seems to happen with the right side extruder. Try printing this, just unzip the .cube3 onto a thumb drive and use...
    48 replies | 788 view(s)
More Activity
About Mythandar

Basic Information

Statistics


Total Posts
Total Posts
229
Posts Per Day
1.14
General Information
Last Activity
Yesterday 05:26 AM
Join Date
01-30-2017
Referrals
1

1 Friend

  1. MegaloDon MegaloDon is offline

    Expert 3D Printer

    MegaloDon
Showing Friends 1 to 1 of 1

07-31-2017


07-24-2017