Tab Content
  • MegaloDon's Avatar
    04-12-2018, 10:05 PM
    MegaloDon replied to a thread BFB (G-Code) for Cube 3 in Cube3
    I think this is the last straw for me. Life is too short for all this drama. Oh, and by the way... My dog's breath smells like cat poop.
    80 replies | 7510 view(s)
  • MegaloDon's Avatar
    04-11-2018, 12:43 AM
    MegaloDon replied to a thread BFB (G-Code) for Cube 3 in Cube3
    My cat's breath smells like cat food.
    80 replies | 7510 view(s)
  • MegaloDon's Avatar
    04-10-2018, 03:08 AM
    MegaloDon replied to a thread Aftermarket build plate? in Cube3
    https://support.3dsystems.com/s/article/Cube-3-Ekocycle-Best-Practices For a good z-gap, you should be able to slide through the gap gauge (from ...
    65 replies | 6241 view(s)
  • MegaloDon's Avatar
    04-10-2018, 01:10 AM
    MegaloDon replied to a thread Aftermarket build plate? in Cube3
    From here >>> http://www.print3dforum.com/showthread.php/900-Cube3-Filament-*SOFTWARE*-Hack-is-here!!!?p=43316&viewfull=1#post43316 "Secret" to me...
    65 replies | 6241 view(s)
  • MegaloDon's Avatar
    04-09-2018, 10:25 PM
    MegaloDon replied to a thread Aftermarket build plate? in Cube3
    I don't think the problem is with G70. TD has his own opinions on things and thinks his ideas are the only good ones. G70 was simply stating facts...
    65 replies | 6241 view(s)
  • MegaloDon's Avatar
    04-06-2018, 06:43 AM
    MegaloDon replied to a thread BFB (G-Code) for Cube 3 in Cube3
    @JohnTee, I think tprothma has a really good handle on the inner workings of BFB code. He has done a lot of research and has had great results. ...
    80 replies | 7510 view(s)
  • Mythandar's Avatar
    04-04-2018, 03:47 AM
    Mythandar replied to a thread [ HOW TO ] Use other slicers with cube 3 in Cube3
    Sorry about that, here's the link again. http://www.print3dforum.com/showthread.php/1002-Cube-Print-Temperature-Modifier-*beta* I was posting from...
    290 replies | 43203 view(s)
  • Mythandar's Avatar
    04-03-2018, 05:59 PM
    Mythandar replied to a thread [ HOW TO ] Use other slicers with cube 3 in Cube3
    If your trying to decode a .cube3 file that was made in cubeprint then check out this thread/program...
    290 replies | 43203 view(s)
  • Mythandar's Avatar
    04-03-2018, 06:26 AM
    Mythandar replied to a thread [ HOW TO ] Use other slicers with cube 3 in Cube3
    Well I don't know where Cura-Cube3-fix, came from but essentially yes. When I made the information in the first post, the new cura 2.x wasn't able...
    290 replies | 43203 view(s)
No More Results
About Mythandar

Basic Information

Statistics


Total Posts
Total Posts
244
Posts Per Day
0.54
General Information
Last Activity
04-04-2018 05:07 AM
Join Date
01-30-2017
Referrals
2

1 Friend

  1. MegaloDon MegaloDon is offline

    Expert 3D Printer

    MegaloDon
Showing Friends 1 to 1 of 1
No results to show...