Tab Content
  • ztoddman1's Avatar
    01-11-2018, 04:55 PM
    how bad will it erode the nozzle? seems like I read somewhere that this filament is an abrasive.
    72 replies | 2942 view(s)
  • ztoddman1's Avatar
    01-05-2018, 01:36 PM
    ztoddman1 replied to a thread [ THING ] HubCap V1 in Cube3
    was adjusting the height of it using that guide and this wonderful frigid weather has my fingers cracked and didn't get a good grip on it. I'll find...
    56 replies | 1671 view(s)
  • ztoddman1's Avatar
    01-05-2018, 01:34 AM
    ztoddman1 replied to a thread [ THING ] HubCap V1 in Cube3
    I called it a nut, its that one that goes around the hot end that the spring is against. THIS...
    56 replies | 1671 view(s)
  • ztoddman1's Avatar
    01-04-2018, 10:05 PM
    ztoddman1 replied to a thread [ THING ] HubCap V1 in Cube3
    i finally got the clip to print. Had to rotate it, flip it, spin, etc to make it work but I got it. I tinkered with your nozzle to accept the M5 push...
    56 replies | 1671 view(s)
  • ztoddman1's Avatar
    01-02-2018, 01:51 PM
    ztoddman1 replied to a thread [ THING ] HubCap V1 in Cube3
    No jams, just stopped like it was completed but only half was way finished. I tried on the right side filament and it worked.
    56 replies | 1671 view(s)
  • ztoddman1's Avatar
    01-02-2018, 12:40 AM
    ztoddman1 replied to a thread [ THING ] HubCap V1 in Cube3
    -- Yessir! Tried to print your hubcap, it stopped about 1/2 way, will attempt it with the other side and see if it works. Did get the nozzle and...
    56 replies | 1671 view(s)
  • ztoddman1's Avatar
    01-02-2018, 12:37 AM
    ztoddman1 replied to a thread Solid prints - Lothiphane in Cube3
    Nope- Short to the point.
    4 replies | 102 view(s)
  • ztoddman1's Avatar
    12-31-2017, 12:07 PM
    ztoddman1 replied to a thread [ THING ] HubCap V1 in Cube3
    great! Go PENS.
    56 replies | 1671 view(s)
  • ztoddman1's Avatar
    12-31-2017, 02:02 AM
    ztoddman1 replied to a thread [ THING ] HubCap V1 in Cube3
    Lawd, step away for a few days and what a surprise when I came back! Awesome work Z, can not wait to run this puppy tonight! Where did you put the...
    56 replies | 1671 view(s)
  • ztoddman1's Avatar
    12-21-2017, 03:59 PM
    ztoddman1 replied to a thread [ THING ] HubCap V1 in Cube3
    Darn right, that looks sexy. Cant wait for the files!! Keep up the good work my man!
    56 replies | 1671 view(s)
No More Results
About ztoddman1

Basic Information

Statistics


Total Posts
Total Posts
78
Posts Per Day
0.46
General Information
Last Activity
Today 06:11 AM
Join Date
07-31-2017
Referrals
0

01-02-2018


12-22-2017


12-21-2017


12-17-2017


12-16-2017