Tab Content
  • JackMeoff's Avatar
    04-12-2018, 01:09 AM
    JackMeoff replied to a thread BFB (G-Code) for Cube 3 in Cube3
    No. I'm contributing to the thread. Again, you just don't quite get it. You have to precede the message with "@user" for others to know it is...
    80 replies | 7501 view(s)
  • JackMeoff's Avatar
    04-11-2018, 11:42 PM
    JackMeoff replied to a thread BFB (G-Code) for Cube 3 in Cube3
    That's what I have been saying all along. Look at my previous post of the manual. That was a complete capture from a PDF file of the 3D Systems...
    80 replies | 7501 view(s)
  • JackMeoff's Avatar
    04-10-2018, 09:57 PM
    JackMeoff replied to a thread BFB (G-Code) for Cube 3 in Cube3
    I have an idea. Let's have some fun. How about we have a print off ? Everyone who has a Cube 3 or an Eco can participate. Every Firmware has the...
    80 replies | 7501 view(s)
  • JackMeoff's Avatar
    04-10-2018, 05:09 PM
    JackMeoff replied to a thread BFB (G-Code) for Cube 3 in Cube3
    @Tim Yep. For S****&Grins. I used your S3D settings changing only the Gap. Note, I use a "LokBuild" on my build plate. I set the Gap to .23 as...
    80 replies | 7501 view(s)
  • JackMeoff's Avatar
    04-09-2018, 08:50 PM
    JackMeoff replied to a thread Aftermarket build plate? in Cube3
    "The rest of the audience is free to follow or not given advices on this or any other matter." This is absolutely correct. However, proper Internet...
    65 replies | 6231 view(s)
  • JackMeoff's Avatar
    04-07-2018, 11:27 PM
    JackMeoff replied to a thread Aftermarket build plate? in Cube3
    How's this scenario... Remove ur build plate Run Auto Cal "MANUALLY" like I said and set the gap 2 inches from the print nozzle Save by checking...
    65 replies | 6231 view(s)
  • JackMeoff's Avatar
    04-07-2018, 11:04 PM
    JackMeoff replied to a thread [ HOW TO ] Use other slicers with cube 3 in Cube3
    @Tim I volunteered you to answer JTs questions on the BFB thread. Don't get too pissed. OK? G70
    290 replies | 43154 view(s)
  • JackMeoff's Avatar
    04-07-2018, 11:00 PM
    JackMeoff replied to a thread BFB (G-Code) for Cube 3 in Cube3
    @JT Hang tight... Tim will answer all ur questions. G70
    80 replies | 7501 view(s)
  • JackMeoff's Avatar
    04-07-2018, 04:16 PM
    @Kiza Check ur gmail... G70
    46 replies | 2458 view(s)
  • JackMeoff's Avatar
    04-05-2018, 07:19 PM
    JackMeoff replied to a thread Aftermarket build plate? in Cube3
    Tom, You are certainly entitled to your opinion. However, I would have a tendency to rely what is written in the manual. Following the above...
    65 replies | 6231 view(s)
  • JackMeoff's Avatar
    04-05-2018, 06:37 PM
    JackMeoff replied to a thread Aftermarket build plate? in Cube3
    @MarkRon And that 'Auto Cal' feature isn't even in the manual hahaha, how strange. Straight out of the manual: For this procedure, you will...
    65 replies | 6231 view(s)
  • JackMeoff's Avatar
    04-04-2018, 08:10 PM
    @Kiza By the way, does anybody know, what are the settings for movement/extrusion? Steps per mm in Cube 3 firmware. The Cube firmware uses...
    46 replies | 2458 view(s)
No More Results
About JackMeoff

Basic Information

Statistics


Total Posts
Total Posts
38
Posts Per Day
0.18
General Information
Last Activity
04-22-2018 09:11 PM
Join Date
09-28-2017
Referrals
0

04-09-2018


04-08-2018


04-05-2018


03-25-2018