Tab Content
  • tprothma's Avatar
    04-12-2018, 05:42 PM
    tprothma replied to a thread BFB (G-Code) for Cube 3 in Cube3
    I usually don't respond at all to these sort of things and only offer my facts, judgement, experience and help when I can. First of all I hope...
    79 replies | 7334 view(s)
  • tprothma's Avatar
    04-11-2018, 10:27 PM
    tprothma replied to a thread BFB (G-Code) for Cube 3 in Cube3
    Cal (auto or manual) sets the zero point, then every layer is indexed from that same zero point. 0.02mm seems reasonable, even if the mylar is...
    79 replies | 7334 view(s)
  • tprothma's Avatar
    04-11-2018, 09:42 PM
    tprothma replied to a thread BFB (G-Code) for Cube 3 in Cube3
    Yes I'd think gap gauge non-sticker portion for those that can't do autocal is the right starting point. Everyone else that can get autocal to work...
    79 replies | 7334 view(s)
  • tprothma's Avatar
    04-11-2018, 05:58 PM
    tprothma replied to a thread BFB (G-Code) for Cube 3 in Cube3
    Hi all, I think there is some debate about gap settings. Gap fixes only first layer and there are more robust ways to fix this with the BFB tweaker...
    79 replies | 7334 view(s)
  • tprothma's Avatar
    04-10-2018, 10:04 PM
    tprothma replied to a thread BFB (G-Code) for Cube 3 in Cube3
    G70, thanks I appreciate the feedback. Keep in mind it's based on collaboration and help from you and MegaloDon along with all the other hard work...
    79 replies | 7334 view(s)
  • tprothma's Avatar
    04-10-2018, 05:41 AM
    tprothma replied to a thread BFB (G-Code) for Cube 3 in Cube3
    3DS uses 0.5mm which is calculated with a little trig from BFB code directly from CubePrint. I think you inadvertently helped fusing by using...
    79 replies | 7334 view(s)
  • tprothma's Avatar
    04-09-2018, 11:40 PM
    tprothma replied to a thread BFB (G-Code) for Cube 3 in Cube3
    In many cases stock PLA through CubePrint outer layer can be peeled from the second layer, so even the baseline needs a little tuning. I don't think...
    79 replies | 7334 view(s)
  • tprothma's Avatar
    04-09-2018, 04:07 PM
    tprothma replied to a thread BFB (G-Code) for Cube 3 in Cube3
    Hey John, sorry if I took your response too literally. Printrbot filament is the other one I've printed with and have fine tuning parameters. Tim
    79 replies | 7334 view(s)
  • tprothma's Avatar
    04-08-2018, 05:07 AM
    tprothma replied to a thread BFB (G-Code) for Cube 3 in Cube3
    John, it actually is frosted mini-wheats. If you try to print amolen with stock 3DS PLA settings it won't fuse well, and will look very stringy and...
    79 replies | 7334 view(s)
  • tprothma's Avatar
    04-07-2018, 11:39 PM
    tprothma replied to a thread BFB (G-Code) for Cube 3 in Cube3
    I've been really busy with a lot of things at work and still look like I'll be busy for a while, so I've actually had limited time to dedicate to...
    79 replies | 7334 view(s)
  • tprothma's Avatar
    04-07-2018, 10:39 PM
    tprothma replied to a thread [ HOW TO ] Use other slicers with cube 3 in Cube3
    Sorry Tommy, actually not related menus in general. Much like G codes, these special M codes tell the firmware what to tell the hardware to do. ...
    290 replies | 42775 view(s)
  • tprothma's Avatar
    04-04-2018, 04:13 PM
    tprothma replied to a thread [ HOW TO ] Use other slicers with cube 3 in Cube3
    JohnTee, send me your BFB and I'll swap left to right for you. Basically this is what needs to be done, and I can do the hand edits easier than...
    290 replies | 42775 view(s)
  • tprothma's Avatar
    04-04-2018, 04:14 AM
    tprothma replied to a thread [ HOW TO ] Use other slicers with cube 3 in Cube3
    Hi John, swwinterry's decoder works for me (32bit only), Mythandar's encoder works for me also only 32bit...
    290 replies | 42775 view(s)
No More Results
About tprothma

Basic Information

Statistics


Total Posts
Total Posts
46
Posts Per Day
0.48
General Information
Last Activity
Today 07:54 AM
Join Date
01-17-2018
Referrals
1

04-08-2018