Tab Content
  • JohnTee's Avatar
    Today, 06:32 AM
    JohnTee replied to a thread BFB (G-Code) for Cube 3 in Cube3
    Cube 3 Data: I ran some test files to measure the relation between movement speed and the "F" value in the bfb G1 commands. Summary: Approximately...
    103 replies | 9001 view(s)
  • JohnTee's Avatar
    Yesterday, 03:52 AM
    Fantastic! I'm off to print mine now. Oh... I don't have a print file, yet!! :rolleyes: And, no, I don't know what flaw you might be thinking...
    30 replies | 920 view(s)
  • JohnTee's Avatar
    Yesterday, 03:46 AM
    I believe the Cube 3 is Left-handed!! Mine can't seem to reach the waste bin when I print on the right side -- it purges over the edge of the...
    2 replies | 36 view(s)
  • JohnTee's Avatar
    05-17-2018, 02:44 PM
    Thank you!! I'm on my way to HF... Funny thing, I searched their website but did not find these bits - only bigger ones.
    30 replies | 920 view(s)
  • JohnTee's Avatar
    05-17-2018, 03:28 AM
    JohnTee replied to a thread .cube3 file decoder in Cube3
    At least!! Not sure how I got it wrong - probably used cubeencoder instead of cubedecoder. I've learned there is a difference...
    25 replies | 2603 view(s)
  • JohnTee's Avatar
    05-17-2018, 03:25 AM
    JohnTee replied to a thread The Ekocycle Cube Thread in Cube3
    (Excuse me, the cartridges do not have to be modified when going to cube 3?) Yes, you must modify the cartridges. The Cube3 firmware will not...
    29 replies | 1401 view(s)
  • JohnTee's Avatar
    05-17-2018, 02:59 AM
    JohnTee replied to a thread BFB (G-Code) for Cube 3 in Cube3
    Good Find, boilerbots! Thanks for sharing. (Hm. Internet Archive -- good thinking! :)
    103 replies | 9001 view(s)
  • JohnTee's Avatar
    05-17-2018, 02:44 AM
    I've made my parts - with Ekocycle filament. It required a bit of clean-up. Thanks, TD, for choosing a standard thread for the cap! I was able to use...
    30 replies | 920 view(s)
  • JohnTee's Avatar
    05-16-2018, 05:37 AM
    Thank you for a fine set of instructions, TD. I am printing the parts now, will let you know how it goes. BTW, is the rectangular object in the...
    30 replies | 920 view(s)
  • JohnTee's Avatar
    05-16-2018, 04:30 AM
    JohnTee replied to a thread .cube3 file decoder in Cube3
    Everybody probably knows this, but... FWIW, I just found that cubedecoder works for Ekocycle .cube3 files! (I had thought it wouldn't, but my...
    25 replies | 2603 view(s)
  • JohnTee's Avatar
    05-16-2018, 01:44 AM
    Thanks for sharing, TD. I'm still missing something... Do you use the steel/aluminum nozzle from a Cube3 cartridge inside the 'hotend core' part? If...
    30 replies | 920 view(s)
  • JohnTee's Avatar
    05-12-2018, 08:02 PM
    Great video, Tom! Questions!! - that nozzle holder looks different from the one I made a while back which uses a regular 6mm x 4mm teflon...
    30 replies | 920 view(s)
  • JohnTee's Avatar
    05-12-2018, 07:27 PM
    JohnTee replied to a thread The Ekocycle Cube Thread in Cube3
    Here's how to switch Ekocycle to Cube 3: ...
    29 replies | 1401 view(s)
  • JohnTee's Avatar
    05-12-2018, 03:46 AM
    JohnTee replied to a thread BFB (G-Code) for Cube 3 in Cube3
    I have not. In fact, I don't know how to do this! Does "3DS driver" refer to a piece of the Windows 10 3D print program I've seen mentioned,...
    103 replies | 9001 view(s)
  • JohnTee's Avatar
    05-10-2018, 01:26 AM
    JohnTee replied to a thread BFB (G-Code) for Cube 3 in Cube3
    I believe they are just another form of comment. It doesn't seem to matter if they aren't there. Does the Cube actually do a Z lift on...
    103 replies | 9001 view(s)
  • JohnTee's Avatar
    05-09-2018, 06:51 PM
    JohnTee replied to a thread BFB (G-Code) for Cube 3 in Cube3
    A bit more info on BFB codes - this from the BFB Axon 2 User Manual (thanks to G70 and MegaloDon for pointing out the treasure trove of info!) Most...
    103 replies | 9001 view(s)
  • JohnTee's Avatar
    05-09-2018, 03:48 AM
    <sidetrack warning!> Please ignore if this would get the discussion off track!! @boilerbots - What version of Cura are you using to make your .bfb...
    7 replies | 258 view(s)
  • JohnTee's Avatar
    04-24-2018, 04:37 AM
    JohnTee replied to a thread BFB (G-Code) for Cube 3 in Cube3
    Suggestions for the Codes table in Post #1: M101 - Left extruder on M201 - Right extruder on M103 - Extruders off, and retract per current M227...
    103 replies | 9001 view(s)
No More Results
About JohnTee

Basic Information

Statistics


Total Posts
Total Posts
59
Posts Per Day
0.66
General Information
Last Activity
Today 06:32 AM
Join Date
02-23-2018
Referrals
0

05-17-2018


05-12-2018


04-20-2018


04-19-2018