Tab Content
  • JohnTee's Avatar
    02-10-2019, 05:59 AM
    JohnTee replied to a thread [ HOW TO ] Building Tomuro's Circuit. in Cube3
    A small suggestion: if the area that holds the contacts could be configured such that they could flex independently (ie, a split between them?...
    10 replies | 323 view(s)
  • JohnTee's Avatar
    02-09-2019, 03:35 PM
    JohnTee replied to a thread [ HOW TO ] Building Tomuro's Circuit. in Cube3
    We now take time out for a non-announcement... :)
    10 replies | 323 view(s)
  • JohnTee's Avatar
    02-08-2019, 09:51 PM
    JohnTee replied to a thread The Ekocycle Cube Thread in Cube3
    Very nice!!! So elegant compared to my attempt! Does it hold itself in place, or do you hold it down with your hand to make contact? Is your...
    34 replies | 4224 view(s)
  • JohnTee's Avatar
    02-07-2019, 05:16 AM
    JohnTee replied to a thread [ HOW TO ] Building Tomuro's Circuit. in Cube3
    TD, I'm sorry I haven't been engaged, to try to help. We have sort of a small family health crisis (dad in law) going on, so I'm a bit busy. Anyway,...
    10 replies | 323 view(s)
  • JohnTee's Avatar
    02-03-2019, 10:55 PM
    JohnTee replied to a thread [ HOW TO ] Building Tomuro's Circuit. in Cube3
    Yep, all the +5v you need comes from the nano - pin 27 (4th from the top righthand corner... :p ) We're proud of you for taking this great step,...
    10 replies | 323 view(s)
  • JohnTee's Avatar
    02-03-2019, 10:45 PM
    JohnTee replied to a thread Ultimaker Cura for Cube3... in Cube3
    Another way to look at it? From a chart by MegaloDon ( http://www.print3dforum.com/showthread.php/935-BFB-(G-Code)-for-Cube-3 ), the...
    10 replies | 934 view(s)
  • JohnTee's Avatar
    02-01-2019, 02:22 AM
    JohnTee replied to a thread Ultimaker Cura for Cube3... in Cube3
    I agree completely that Cura is worth pursuing, not the least for the security of having an alternate method to generate print files. Thank you for...
    10 replies | 934 view(s)
  • JohnTee's Avatar
    01-31-2019, 06:00 AM
    JohnTee replied to a thread Ultimaker Cura for Cube3... in Cube3
    I used Cura 3.6 to slice my little test cubelet, cobbled up the bfb file, encoded and printed. It came out not-too-bad. Not as nice as Cube Print...
    10 replies | 934 view(s)
  • JohnTee's Avatar
    01-29-2019, 05:05 AM
    JohnTee replied to a thread Cube Glue in Cube3
    That's a fantastic glue shaker -- Scale it up some, and you can sell it to the Home Depot paint department! :p BTW, I think it was someone else...
    3 replies | 215 view(s)
  • JohnTee's Avatar
    01-28-2019, 01:25 AM
    JohnTee replied to a thread Ultimaker Cura for Cube3... in Cube3
    So you are actually printing Cura files? Impressive! Can you share how you set Cura up to do this, and what you have to do between Cura and...
    10 replies | 934 view(s)
  • JohnTee's Avatar
    01-18-2019, 05:10 AM
    JohnTee replied to a thread The Printing Lounge in Cube3
    Ooohhhh - never noticed that little light bulb icon Thanks - now I can see what's printing!!
    196 replies | 29507 view(s)
  • JohnTee's Avatar
    01-17-2019, 04:12 PM
    JohnTee replied to a thread The Printing Lounge in Cube3
    I think my two Cube 3's are possessed! Up to last week, the decoration lights stayed on the whole time they were printing or purging or whatever....
    196 replies | 29507 view(s)
  • JohnTee's Avatar
    01-17-2019, 04:04 PM
    JohnTee replied to a thread Cube3 File Editing in Cube3
    Thanks for gathering this together, TD. Note: I keep a shortcut on the corner of the Desktop for the decoder and encoder programs. When I drag a...
    2 replies | 198 view(s)
  • JohnTee's Avatar
    01-16-2019, 08:34 PM
    JohnTee replied to a thread The Ekocycle Cube Thread in Cube3
    Aw, shucks...I can't figure out how to clip them on to my chip! :rolleyes:
    34 replies | 4224 view(s)
No More Results
About JohnTee

Basic Information

Statistics


Total Posts
Total Posts
140
Posts Per Day
0.39
General Information
Last Activity
02-12-2019 05:18 AM
Join Date
02-23-2018
Referrals
0

02-10-2019


01-24-2019