Tab Content
  • JohnTee's Avatar
    01-18-2019, 05:10 AM
    JohnTee replied to a thread The Printing Lounge in Cube3
    Ooohhhh - never noticed that little light bulb icon Thanks - now I can see what's printing!!
    196 replies | 27462 view(s)
  • JohnTee's Avatar
    01-17-2019, 04:12 PM
    JohnTee replied to a thread The Printing Lounge in Cube3
    I think my two Cube 3's are possessed! Up to last week, the decoration lights stayed on the whole time they were printing or purging or whatever....
    196 replies | 27462 view(s)
  • JohnTee's Avatar
    01-17-2019, 04:04 PM
    JohnTee replied to a thread Cube3 File Editing in Cube3
    Thanks for gathering this together, TD. Note: I keep a shortcut on the corner of the Desktop for the decoder and encoder programs. When I drag a...
    2 replies | 46 view(s)
  • JohnTee's Avatar
    01-16-2019, 08:34 PM
    JohnTee replied to a thread The Ekocycle Cube Thread in Cube3
    Aw, shucks...I can't figure out how to clip them on to my chip! :rolleyes:
    32 replies | 3641 view(s)
  • JohnTee's Avatar
    01-15-2019, 06:05 PM
    Nice sleuthing! Would you use the 6.5x6.5 which is 5mm smaller than the Cube3 print bed?
    4 replies | 51 view(s)
  • JohnTee's Avatar
    01-15-2019, 05:53 AM
    It may be necessary to also use clips on the front and back edges to keep it flat, even with magnets in the middle.
    4 replies | 51 view(s)
  • JohnTee's Avatar
    01-15-2019, 05:25 AM
    JohnTee replied to a thread BFB (G-Code) for Cube 3 in Cube3
    What do the three columns represent? It looks like it might be "Cube3", "Ekocycle", and "???" Cube PLA uses M227 P450 S450 G450 F600 M227...
    124 replies | 18980 view(s)
  • JohnTee's Avatar
    01-13-2019, 05:28 AM
    JohnTee replied to a thread Familiar shape.... in Cube3
    Proprietary "chipped" cartridges??
    3 replies | 78 view(s)
  • JohnTee's Avatar
    01-13-2019, 05:13 AM
    JohnTee replied to a thread Useful Mod to .CUBE3 file in Cube3
    Good summary, TD. Nice to have it all in one place. FWIW -- I've found the only necessary header changes are PrinterModel and MaterialCodeEx...
    1 replies | 107 view(s)
  • JohnTee's Avatar
    01-13-2019, 04:29 AM
    JohnTee replied to a thread The Printing Lounge in Cube3
    No, just a select-and-delete using Regex. Most of the steps are just to find the start of the binary blob . The Ctrl-Shift-End is the trick to...
    196 replies | 27462 view(s)
  • JohnTee's Avatar
    01-13-2019, 03:51 AM
    JohnTee replied to a thread The Printing Lounge in Cube3
    Try this: <Macro name="Remove End Gibberish" Ctrl="no" Alt="no" Shift="no" Key="0"> <Action type="3" message="1700"...
    196 replies | 27462 view(s)
  • JohnTee's Avatar
    01-13-2019, 02:07 AM
    JohnTee replied to a thread The Printing Lounge in Cube3
    FWIW-- Here's the code for an example Notepad++ macro which I use to modify a Cube Print-generated PLA .bfb file for a different PLA material. It:...
    196 replies | 27462 view(s)
  • JohnTee's Avatar
    01-06-2019, 04:12 AM
    JohnTee replied to a thread Help with 3D Builder in Cube3
    CubePro 2.02 looks interesting. I like that you can select different materials. However, when I select Print over USB, the Print Dialog does not...
    5 replies | 167 view(s)
  • JohnTee's Avatar
    01-03-2019, 05:09 AM
    JohnTee replied to a thread OverBrim - Glue Saver in Cube3
    There's no feeling like walking along the edge of a cliff!! ;o)
    1 replies | 44 view(s)
  • JohnTee's Avatar
    01-03-2019, 05:01 AM
    JohnTee replied to a thread Daily Print Sagas in Cube3
    One of my printers decided to go rogue... I started to print some pieces for a spool holder with my new polylite PETG, and after I did the normal...
    149 replies | 23958 view(s)
  • JohnTee's Avatar
    01-03-2019, 04:47 AM
    JohnTee replied to a thread Filament Review in Cube3
    Summary: MatterHackers/polymaker polylite PETG - works good. I ordered a spool of PETG from MatterHackers, and received (ta-daa) a spool with the...
    165 replies | 28452 view(s)
  • JohnTee's Avatar
    12-28-2018, 04:11 AM
    JohnTee replied to a thread Help with 3D Builder in Cube3
    Thanks, TD. I still have a lot of fiddling around to do. I'll take a look at CubePro 2.02, as well. At least it did start a print from 3DB...
    5 replies | 167 view(s)
  • JohnTee's Avatar
    12-27-2018, 06:39 AM
    JohnTee started a thread Help with 3D Builder in Cube3
    Microsoft's 3D Builder program comes pretty much void of any instructions. I could use some pointers! So far: - booted up a 2 year old .ISO of...
    5 replies | 167 view(s)
  • JohnTee's Avatar
    12-23-2018, 09:34 PM
    JohnTee replied to a thread The Printing Lounge in Cube3
    Thank You! You are the Everready Bunnie of 3D Printing Information...! PTFE is ordered. As far as groovin', it goes tolerably well using my...
    196 replies | 27462 view(s)
  • JohnTee's Avatar
    12-23-2018, 05:17 AM
    JohnTee replied to a thread The Printing Lounge in Cube3
    Hey Tom, After Christmas, when you have time, could you post an .stl for this: ...
    196 replies | 27462 view(s)
No More Results
About JohnTee

Basic Information

Statistics


Total Posts
Total Posts
130
Posts Per Day
0.39
General Information
Last Activity
01-18-2019 11:33 PM
Join Date
02-23-2018
Referrals
0

12-25-2018