Tab Content
  • JohnTee's Avatar
    05-24-2018, 07:51 AM
    JohnTee replied to a thread [ HOW TO ] Use other slicers with cube 3 in Cube3
    Back to "Using Other Slicers". But, not exactly Other slicers, rather using CubePrint in a different way. Some of us have noticed that the...
    309 replies | 47129 view(s)
  • JohnTee's Avatar
    05-24-2018, 03:26 AM
    JohnTee replied to a thread BFB (G-Code) for Cube 3 in Cube3
    You did describe the dropping action before -- I kind of forgot! This was the first example where I actually saw it happen. I agree it must be a...
    105 replies | 9121 view(s)
  • JohnTee's Avatar
    05-23-2018, 06:32 AM
    JohnTee replied to a thread BFB (G-Code) for Cube 3 in Cube3
    Cube 3 Data: I ran some test files to measure the relation between movement speed and the "F" value in the bfb G1 commands. Summary: Approximately...
    105 replies | 9121 view(s)
  • JohnTee's Avatar
    05-22-2018, 03:52 AM
    Fantastic! I'm off to print mine now. Oh... I don't have a print file, yet!! :rolleyes: And, no, I don't know what flaw you might be thinking...
    30 replies | 1011 view(s)
  • JohnTee's Avatar
    05-22-2018, 03:46 AM
    I believe the Cube 3 is Left-handed!! Mine can't seem to reach the waste bin when I print on the right side -- it purges over the edge of the...
    2 replies | 44 view(s)
  • JohnTee's Avatar
    05-17-2018, 02:44 PM
    Thank you!! I'm on my way to HF... Funny thing, I searched their website but did not find these bits - only bigger ones.
    30 replies | 1011 view(s)
  • JohnTee's Avatar
    05-17-2018, 03:28 AM
    JohnTee replied to a thread .cube3 file decoder in Cube3
    At least!! Not sure how I got it wrong - probably used cubeencoder instead of cubedecoder. I've learned there is a difference...
    25 replies | 2646 view(s)
  • JohnTee's Avatar
    05-17-2018, 03:25 AM
    JohnTee replied to a thread The Ekocycle Cube Thread in Cube3
    (Excuse me, the cartridges do not have to be modified when going to cube 3?) Yes, you must modify the cartridges. The Cube3 firmware will not...
    29 replies | 1420 view(s)
  • JohnTee's Avatar
    05-17-2018, 02:59 AM
    JohnTee replied to a thread BFB (G-Code) for Cube 3 in Cube3
    Good Find, boilerbots! Thanks for sharing. (Hm. Internet Archive -- good thinking! :)
    105 replies | 9121 view(s)
  • JohnTee's Avatar
    05-17-2018, 02:44 AM
    I've made my parts - with Ekocycle filament. It required a bit of clean-up. Thanks, TD, for choosing a standard thread for the cap! I was able to use...
    30 replies | 1011 view(s)
  • JohnTee's Avatar
    05-16-2018, 05:37 AM
    Thank you for a fine set of instructions, TD. I am printing the parts now, will let you know how it goes. BTW, is the rectangular object in the...
    30 replies | 1011 view(s)
  • JohnTee's Avatar
    05-16-2018, 04:30 AM
    JohnTee replied to a thread .cube3 file decoder in Cube3
    Everybody probably knows this, but... FWIW, I just found that cubedecoder works for Ekocycle .cube3 files! (I had thought it wouldn't, but my...
    25 replies | 2646 view(s)
  • JohnTee's Avatar
    05-16-2018, 01:44 AM
    Thanks for sharing, TD. I'm still missing something... Do you use the steel/aluminum nozzle from a Cube3 cartridge inside the 'hotend core' part? If...
    30 replies | 1011 view(s)
  • JohnTee's Avatar
    05-12-2018, 08:02 PM
    Great video, Tom! Questions!! - that nozzle holder looks different from the one I made a while back which uses a regular 6mm x 4mm teflon...
    30 replies | 1011 view(s)
  • JohnTee's Avatar
    05-12-2018, 07:27 PM
    JohnTee replied to a thread The Ekocycle Cube Thread in Cube3
    Here's how to switch Ekocycle to Cube 3: ...
    29 replies | 1420 view(s)
  • JohnTee's Avatar
    05-12-2018, 03:46 AM
    JohnTee replied to a thread BFB (G-Code) for Cube 3 in Cube3
    I have not. In fact, I don't know how to do this! Does "3DS driver" refer to a piece of the Windows 10 3D print program I've seen mentioned,...
    105 replies | 9121 view(s)
  • JohnTee's Avatar
    05-10-2018, 01:26 AM
    JohnTee replied to a thread BFB (G-Code) for Cube 3 in Cube3
    I believe they are just another form of comment. It doesn't seem to matter if they aren't there. Does the Cube actually do a Z lift on...
    105 replies | 9121 view(s)
  • JohnTee's Avatar
    05-09-2018, 06:51 PM
    JohnTee replied to a thread BFB (G-Code) for Cube 3 in Cube3
    A bit more info on BFB codes - this from the BFB Axon 2 User Manual (thanks to G70 and MegaloDon for pointing out the treasure trove of info!) Most...
    105 replies | 9121 view(s)
  • JohnTee's Avatar
    05-09-2018, 03:48 AM
    <sidetrack warning!> Please ignore if this would get the discussion off track!! @boilerbots - What version of Cura are you using to make your .bfb...
    7 replies | 266 view(s)
No More Results
About JohnTee

Basic Information

Statistics


Total Posts
Total Posts
61
Posts Per Day
0.66
General Information
Last Activity
Yesterday 06:02 AM
Join Date
02-23-2018
Referrals
0

05-17-2018


05-12-2018