dougk12
3D Printer Noob
Find latest postsMini Statistics
- Join Date
- 09-01-2018
- Last Activity
- 03-02-2021 09:37 PM
Recent Visitors
This page has had 5,019 visits
- Tab Content
- dougk12's Activity
- About Me
- Post Thanks / Like
-
Older Activity
-
03-02-2021, 05:27 PMYep, I guess my "idea" is that the printer could be fooled into turning on a heated print bed assembly and then manage that temp by simply turning it...2 replies | 63 view(s) -
03-01-2021, 05:24 PMI did some searches and wasn't able to find anything but it would seem to me that retrofitting a heated bed to CubePro would be feasible. Retrofit =...2 replies | 63 view(s)
-
02-26-2021, 02:42 PMLooks like quite a few people are concerned about the magnets but I found this, which indicates 212f/100c is the limit. Anything above this will...16 replies | 342 view(s)
-
02-23-2021, 04:22 PMI've recently knocked the dust off of my CubePro Trio but my Cube3 will continue to provide the vast majority of my printing, mostly due to the...0 replies | 95 view(s)
-
02-19-2021, 05:15 PMHere are a couple of profiles - One at the default S3D def print speed of 3000mm/sec and another at 4000. I'm playing around with the top speed to...14 replies | 2965 view(s)
-
02-18-2021, 07:28 PMAwesome work! Tempted to try this but without the EE chops, I feel like that would end badly after a few blown weekends :)153 replies | 26975 view(s)
-
02-18-2021, 05:25 PMAwesome^2 Those plans look really good and that Cube 2 conversion is NUTS. The light sensor is an interesting solution. I was thinking more...16 replies | 342 view(s)
-
02-16-2021, 10:20 PMHi Michel I'm also interested in this and I do not believe the heat would impact the earth magnets. I *think* ~225F+ is the heating point that...16 replies | 342 view(s)
-
02-16-2021, 10:06 PMReviving this one because I just pulled my CubePro out of a closet and I am hoping to take full advantage of it and Simplify3D. I broke down and...14 replies | 2965 view(s)
-
02-15-2021, 09:39 PMdougk12 started a thread CubePro external feed and cartridge delete conversion in CubeX / CubePro ForumModels and pictures <---- It's been a while since I've actually used a 3DSystems cartridge (or filament) on my CubePro so I wanted to perform a...0 replies | 88 view(s)
-
02-10-2021, 03:14 PM"Has anyone ever printed with PETG or Polycarbonate /carbon?" PETG, yes. Polycarbonate and Carbon - no. Filament with fiber glass or carbon fiber...9 replies | 585 view(s)
-
02-09-2021, 12:34 PMNever had any issues with off the shelf Nylon in the CubePro (or any other off the shelf filament). Just remember that Nylon needs to be kept dry. I...9 replies | 585 view(s)
-
02-03-2021, 05:25 PMHatchbox and Amazon Basics PLA are my gotos. I also use the Sunlu Silk PLAs but they print at a higher temp. I use Simplify3d but you should be able...9 replies | 585 view(s)
About dougk12
Basic Information
Statistics
Total Posts
- Total Posts
- 24
- Posts Per Day
- 0.03
General Information
- Last Activity
- 03-02-2021 09:37 PM
- Join Date
- 09-01-2018
- Referrals
- 0
02-19-2021
- 07:32 PM - TommyDee clicked Thanks for this post: CubePro And Simplify3d Working by dougk12Here are a couple of...
02-17-2021
- 07:04 PM - RicciEU clicked Likes for this post: Aftermarket filament for CubePro by dougk12"Has anyone ever printed...
- 07:04 PM - RicciEU clicked Thanks for this post: Aftermarket filament for CubePro by dougk12"Has anyone ever printed...
02-16-2021
- 11:09 PM - TommyDee clicked Thanks for this post: heated bed for cube3D by dougk12Hi Michel I'm also...
- 12:58 AM - TommyDee clicked Likes for this post: Aftermarket filament for CubePro by dougk12"Has anyone ever printed...
02-09-2021
- 08:11 PM - TommyDee clicked Thanks for this post: Aftermarket filament for CubePro by dougk12Never had any issues...
02-08-2021
- 09:07 PM - RicciEU clicked Likes for this post: Aftermarket filament for CubePro by dougk12Hatchbox and Amazon...
- 09:06 PM - RicciEU clicked Thanks for this post: Aftermarket filament for CubePro by dougk12Hatchbox and Amazon...