Tab Content
  • dndkeg's Avatar
    09-20-2019, 03:01 AM
    dndkeg replied to a thread The Printing Lounge in Cube3
    Yea I figured :p - - - - - - - - - - Also the 'overtube' fixed the ABS cartridges, I'm surprised 3DS didn't just make the tube super rigid in...
    264 replies | 41878 view(s)
  • dndkeg's Avatar
    09-20-2019, 02:11 AM
    dndkeg replied to a thread The Printing Lounge in Cube3
    I realize that my meaning of mirroring/rotating was talking about taking the file and putting it in a CAD software and ACTUALLY mirroring the part...
    264 replies | 41878 view(s)
  • dndkeg's Avatar
    09-19-2019, 04:55 AM
    dndkeg replied to a thread The Printing Lounge in Cube3
    Gotcha... gonna do that then and cross my fingers that it won't be a repeat... Edit: 9/19/2019 Currently printing the B2B nozzle for the Cube 3...
    264 replies | 41878 view(s)
  • dndkeg's Avatar
    09-19-2019, 02:22 AM
    dndkeg replied to a thread The Printing Lounge in Cube3
    So the 'overtube' from the original cartridge to cover the smaller PTFE tubing would stop the tube from being pushed out?
    264 replies | 41878 view(s)
  • dndkeg's Avatar
    09-18-2019, 09:32 PM
    dndkeg replied to a thread The Printing Lounge in Cube3
    Here's a photo of what it looks like. From the filament gearbox to the plastic piece I salvaged from the cartridge I use a 2mm ID, 3mm OD PTFE Tubing...
    264 replies | 41878 view(s)
  • dndkeg's Avatar
    09-18-2019, 02:50 AM
    dndkeg replied to a thread The Printing Lounge in Cube3
    The reason I'm wondering about this (I found it on the Universal Hub) is because the filament is resisting while printing and pushing the PTFE tube I...
    264 replies | 41878 view(s)
  • dndkeg's Avatar
    09-17-2019, 10:39 PM
    dndkeg replied to a thread The Printing Lounge in Cube3
    Is there any plastic tubing in that brass tubing and is there a tutorial on how to do this? (I'm in the process of converting my cartridges to print...
    264 replies | 41878 view(s)
  • dndkeg's Avatar
    09-17-2019, 10:29 PM
    dndkeg replied to a thread [ HOW TO ] Building Tomuro's Circuit. in Cube3
    I'm trying to find the vector board from the website link provided but I'm not having much luck, do you know the specific part number this board is?
    50 replies | 5306 view(s)
  • dndkeg's Avatar
    09-17-2019, 06:34 AM
    dndkeg replied to a thread The Printing Lounge in Cube3
    I'm assuming you mean a 203mm cause that's the 8" minimum. Also I am still getting used to using some power tools, and the only one that I have on...
    264 replies | 41878 view(s)
  • dndkeg's Avatar
    09-17-2019, 04:35 AM
    dndkeg replied to a thread The Printing Lounge in Cube3
    I think the only hurdle I would need to get over is probably cutting out the magnets which I'm not sure what tool would be useful for that. I did...
    264 replies | 41878 view(s)
  • dndkeg's Avatar
    09-17-2019, 04:07 AM
    dndkeg replied to a thread The Printing Lounge in Cube3
    Looking at the images the bed looks pretty flat, my only concern is that in the third photo where my index finger is, there is a crack in the surface...
    264 replies | 41878 view(s)
  • dndkeg's Avatar
    09-17-2019, 03:05 AM
    dndkeg replied to a thread The Printing Lounge in Cube3
    Any good links to where I can get one that's to size, I rummaged around and found an old print bed that has seen better days, I can definitely...
    264 replies | 41878 view(s)
  • dndkeg's Avatar
    09-15-2019, 11:19 PM
    dndkeg replied to a thread The Printing Lounge in Cube3
    I felt really sad when I saw this not gonna lie... now I HAVE to get the tape and glue, since there's not way to get Cube glue unless it's a third...
    264 replies | 41878 view(s)
  • dndkeg's Avatar
    09-13-2019, 09:09 PM
    dndkeg replied to a thread The Printing Lounge in Cube3
    buddybu was right on, my bad for not showing the quote of the post. I was replying on your rewinding tool that I saw to refill the cartridge spools,...
    264 replies | 41878 view(s)
  • dndkeg's Avatar
    09-13-2019, 06:50 AM
    dndkeg replied to a thread The Printing Lounge in Cube3
    I'm curious as to why you would use this instead of printing straight from the bulk filament spool itself actually
    264 replies | 41878 view(s)
  • dndkeg's Avatar
    09-11-2019, 09:05 AM
    dndkeg replied to a thread The Printing Lounge in Cube3
    Thanks Tommy, I recently joined this forum as I have been basically trying to bring back my Cube 3 from the dead in a sense. I have been looking...
    264 replies | 41878 view(s)
  • dndkeg's Avatar
    09-10-2019, 09:46 PM
    dndkeg replied to a thread The Printing Lounge in Cube3
    Is the blue tape the generic blue painter's tape and does it work with both PLA and ABS?
    264 replies | 41878 view(s)
No More Results
About dndkeg

Basic Information

Statistics


Total Posts
Total Posts
17
Posts Per Day
0.18
General Information
Last Activity
Today 06:36 AM
Join Date
06-20-2019
Referrals
0

09-19-2019


09-17-2019


09-12-2019


09-10-2019