Cube3 running with e3DV6 hotend!

The latest (MK6) print head is better balanced, cooling is increased, LED Lights are properly positioned.
This will be the version to publish.
Hi KIZA have you published the Print Head designs?

I have purchased the SGEN L V2.0 board and TMC2209s to start the modification, your Marlin Config files would help for a novice like me
update
I started the process of converting my Cube 3, kept the original hot end and has been a learning process but even with my lack of expertise the forum post have guided me thru so far
have managed to short a connection and burn fan1 connector, burned all LEDs except for the 12V (not yet), learning to do mesh leveling, updating and configuring the TFT24 to read two nozzles, etc, etc,
THANK YOU ALL FOR THE INFORMATION PUBLISHED IN THIS FORUM !!!
Will post pictures soon
Happy Holidays to all !!

- - - - - - - - - -

my setup is working so far and reading the two heaters individually, however, extruding filament is not working, temperature reading ok (PLA220c, ABS 245c) extruder motors Ok but no filament comes out (E steps at 120, current 650 mA for E0 and E1) - any ideas of where to check my settings ?

UPDATE: now I am Printing... problem appears to be the cartridges and low temperature 3DS filament prints hotter. I was not getting filament flow

Hey there!
Sorry for not posting for a long time, lots of work to do lately.
I wanted to create a nice post with good pictures, etc., and of course never started :D
garufa, I can send you all the stl and config files if you want, you can check my settings.
And I promise I will create a post.

is this possible??? WOW

Kiza wrote: garufa, I can send you all the stl and config files if you want, you can check my settings

- Yes YES and yes, I would like that. I could not figure out how to adapt a Voron's head version to mount the linear rail adapter (forgot to take dimensions after disassembly) see photo, perfect size to match original cube 3 - can you send me a PM with the files?
Attachment 4445Attachment 4446

- - - - - - - - - -

the Voron 0 head version is with a Chimera (2 in 2 out) and also can mount the IR sensor at front, this phot is at the stage I am now using the original head

Attachment 4455

- - - - - - - - - -

Hello Kiza
I have problems with my bed (stock) - when there is not plastic box installed - just the platform and bed - it moves up to position well and start printing; however when i install the plastic box apparently the additional weight triggers the sensor less homing, makes a lot of noise and stops half way up and starts printing on air. only few times have move up Ok. What setting you have on Current and TMC bump sensitivity for the Z axis? you have a heavier plate than the stock pieces i have
I will appreciate your help

- - - - - - - - - -

hello all. I finally completed the Marlin modification, used at the end the latest BTT SKR 2 Rev. B board; I am happy after "sweat and tears" and learn a lot in the process -added at the rear a SD card reader to flash the board without disassembly
thank you all for these posts and instructions.
Attachment 4473 Attachment 4471Attachment 4472

I can't wait to see this in action!! It would be really cool to be able to use off the shelf parts to extend the life of this printer.

Hey there Kiza!
I was just wondering if I could grab the STL files too, I'm looking at installing a similar E3D Chimera hotend too and I would love to see everything you've designed!

Hi there and again sorry for not posting for a long time, been busy a lot.
Here's the link, I'll post the BOM as well.

https://www.thingiverse.com/thing:5824410

Nice work @Kiza! Always good to see you back and with cookies no less ;]

Hey Kiza would you mind posting the limit switch mounts?