Search:

Type: Posts; User: JohnTee

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. On its way! Maxaye, check PM. TommyDee -...

    On its way!

    Maxaye, check PM.

    TommyDee - that would be a brilliant mod!
  2. Ah! There's nothing like a faulty memory chip -...

    Ah! There's nothing like a faulty memory chip - in my head!

    Looking back at my notes, I found that the S/N is encrypted in the cfg.bin file.

    BTW I have two other printers that power up...
  3. FWIW... I ran a diff on BuddyBu's modified...

    FWIW...

    I ran a diff on BuddyBu's modified file vs the version I have been using (if and when I load the Eko firmware.)

    There are three two-byte differences - each just before the CR-LF of a...
  4. I've used the same patched firmware file on the...

    I've used the same patched firmware file on the same usb flash drive on all my Ekocycle machines.

    Where they get particular is if you update files on the internal SD card. Technically the (I...
  5. Ah, thanks for the PETG tip. I'll try some on...

    Ah, thanks for the PETG tip. I'll try some on next order.

    I have Polymaker Polylite red and some Chinese green PETG which works, but I have not perfected the setup yet. I use the cube glue slurry...
  6. If 'Toolbox' means the patch to stop the filament...

    If 'Toolbox' means the patch to stop the filament % countdown, then yes, there is a version for Ekocycle.
    The exact hex mods to the firmware are different in detail, of course, but the effect is the...
  7. Hey Max, FWIW I replied to your PM last night...

    Hey Max,

    FWIW I replied to your PM last night while you were working in this thread. I didn't realize then, but you are MUCH farther along here than I suspected when I replied.

    I agree with the...
  8. Replies
    30
    Views
    98,370

    How goes it -- have you had a chance to try the...

    How goes it -- have you had a chance to try the TPU yet? (anxious followers are awaiting!)
  9. Replies
    30
    Views
    98,370

    Hooray for your engineering 'light bulbs', TD!...

    Hooray for your engineering 'light bulbs', TD! I'm looking forward to whatever it is you are visualizing, as I have found grooving the tube to be the trickiest part of doing a B2B conversion.
    ...
  10. Replies
    30
    Views
    98,370

    Good deal - we'll all be standing by to see how...

    Good deal - we'll all be standing by to see how it works for you.
    What brand did you order and what vendor?

    Oh, and what bowden setup are you using? TommyDee's B2B, perhaps?

    Thanks!
  11. Replies
    30
    Views
    98,370

    Who has printed a TPU filament on the Cube 3, and...

    Who has printed a TPU filament on the Cube 3, and how did it work out?
  12. Replies
    367
    Views
    297,629

    Surprisingly low price. Looks really nice. Is it...

    Surprisingly low price. Looks really nice.
    Is it conductive?? :p:rolleyes:

    ------------------------
    Different question for TD:
    It appears that you prefer respooling the cartridges rather than...
  13. R o t f l !!!

    R o t f l !!!
  14. Good point. Maybe they installed a tiny squirrel...

    Good point.
    Maybe they installed a tiny squirrel in there that turns the shaft with it's teeth?
    If so, mine is in bad need of some dental work!

    ----------------
    BTW, the temperatures are spot...
  15. It gets weirder... When i switched build...

    It gets weirder...

    When i switched build plates, it began to print.
    The one I was using at first was kind of rough, with nozzle dents and grooves from improper Z-gaps. I cleaned and sanded it,...
  16. I did swap out the motherboard, as the original...

    I did swap out the motherboard, as the original was broken. This is the first time I've tried to use it since the swap.
    I am using the same power supply that works with the other two printers.
    If I...
  17. I did swap out the motherboard, as the original...

    I did swap out the motherboard, as the original was broken. This is the first time I've tried to use it since the swap.
    I am using the same power supply that works with the other two printers.
    I...
  18. Thanks, Tom. Since there is nothing in the...

    Thanks, Tom.

    Since there is nothing in the filament path to stop it you have two choices. Extruder clogging or filament motor driver weakness.
    -- I am leaning toward motor weakness. Does...
  19. Do stepper motors get tired and weak with old age??

    I'm working on getting a Cube3/Ekocycle printer going. I had to replace the motherboard -- thanks to help from geofreitag -- to get it working.

    Now, when I try to print, it seems that it cannot...
  20. FWIW, I took a shot at installing CubePrint under...

    FWIW, I took a shot at installing CubePrint under Wine on Linux Mint a while back. As best I remember, I hit a dead end when it insisted it needed a certain version of Internet Explorer (10, I...
  21. Replies
    34
    Views
    122,784

    Brilliant! Didn't think of that, and if I had I...

    Brilliant!
    Didn't think of that, and if I had I would've thought it wouldn't work!

    Nice to be printing again, after a hiatus due to busyness.
  22. Replies
    34
    Views
    122,784

    Good suggestion. Turns out, I had made a bad...

    Good suggestion.

    Turns out, I had made a bad ASSumption about the encoder version buddybu included in the tools folder.
    (Long story follows - skip to end if helpful...)
    I copied the...
  23. Replies
    34
    Views
    122,784

    I'm now having a Windows problem with...

    I'm now having a Windows problem with cube3-encoder on Windows 7 Pro (with September updates.)

    It throws an Error Dialog =
    "The application was unable to start correctly (0x000007b). Click OK to...
  24. Replies
    365
    Views
    380,595

    This obviously is not his first rodeo!! ;)

    This obviously is not his first rodeo!! ;)
  25. Replies
    365
    Views
    380,595

    Got it. That is one nice piece of work, bb! ...

    Got it. That is one nice piece of work, bb!

    Kudos to you, and to TD for all the ideas and info.

    Future tweak - could the Printer Model be a pull-down list?
    If so, then perhaps on selection...
Results 1 to 25 of 196
Page 1 of 8 1 2 3 4