Search:

Type: Posts; User: TommyDee

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    326
    Views
    532,051

    Sticky: You might consider a local STEM program in a...

    You might consider a local STEM program in a local school. Although this is a great offer, and I would take you up on it if it came to $50 or less, a local program for kids and young adults may...
  2. You hear the ticks. It is a process. But you...

    You hear the ticks. It is a process. But you can test it with a border print to see if the filament is equally wide all around as a test.

    I've lain a white sheet of paper on the surface to fool...
  3. Have a look here -...

    Have a look here - http://www.print3dforum.com/showthread.php/1165-Z-ticks?highlight=z-ticks

    I don't ever auto-level.
  4. Replies
    3
    Views
    306

    Some people here have parted out machines and...

    Some people here have parted out machines and offered parts. Sometimes they show up on Ebay. It is hard to find parts. Feel free to post for parts in CubePro for-sale/trade section. Here is a...
  5. Replies
    3
    Views
    306

    This is likely a sensor failure on the motor...

    This is likely a sensor failure on the motor controller board. The system monitors the black and white 'flags' on the filament drive wheels. If that is not getting processed or something is wrong...
  6. Replies
    16
    Views
    15,797

    It is probably a MOV on the heater control...

    It is probably a MOV on the heater control module. Seen that picture before. But the factory 2.02 upgrade was fine, I still run it. I honestly think that settings go out of bounds for the heater...
  7. Replies
    34
    Views
    29,956

    Sticky: You can write a custom g-code (*.cubepro) file...

    You can write a custom g-code (*.cubepro) file that only initiates the heater.
  8. Thread: Wood Filament

    by TommyDee
    Replies
    3
    Views
    544

    Connect with Tamir1an

    Connect with Tamir1an
  9. Aha, now I understand what you are after. I have...

    Aha, now I understand what you are after. I have not captured that print file. Hopefully someone else here has this in their archives and is willing to post it.

    If you want to, you could try to...
  10. All you can do is request the files. The user...

    All you can do is request the files. The user doesn't participate here anymore.

    You are also welcome to check some of my alternatives on thingiverse - https://www.thingiverse.com/qube3bot/designs...
  11. Replies
    8
    Views
    5,517

    Something to do with entering a code?

    Something to do with entering a code?
  12. Replies
    26
    Views
    7,235

    More gap. To little gap presents to the machine...

    More gap. To little gap presents to the machine like a clog.
  13. Replies
    26
    Views
    7,235

    Not from the pictures. You could try unplugging...

    Not from the pictures. You could try unplugging them and see if it boots after that.
  14. Replies
    26
    Views
    7,235

    Looking good so far. I use CubeGlue on my...

    Looking good so far.

    I use CubeGlue on my LokBuild for great service. However, LokBuild does work well without glue with several materials.

    Glue on LokBuild can be recharged by simply misting...
  15. Replies
    9
    Views
    1,521

    The only posts we've seen about failed heaters...

    The only posts we've seen about failed heaters was after the hack so I bet it is the culprit. Not sure how it would do that though. Somewhere in the firmware is where the chamber temperature is...
  16. Replies
    9
    Views
    1,521

    The fan on the heater is on all the time but the...

    The fan on the heater is on all the time but the heater has a thermal fuse internally to stop heating. Technically, it should be hardwired to the AC input.

    I am not sure anyone has investigated...
  17. Replies
    9
    Views
    1,521

    There should be a version 2.02. Yes, .ar is the...

    There should be a version 2.02. Yes, .ar is the right extension and cubepro is the appropriate prefix.
  18. Replies
    9
    Views
    1,521

    We have the Cubify repository stored among us. ...

    We have the Cubify repository stored among us.

    http://www.print3dforum.com/showthread.php/3024-3DS-Cube-File-Links
  19. Print a 6" x 6" border. Two of the magnets under...

    Print a 6" x 6" border. Two of the magnets under the bed are adjustable.
  20. Replies
    26
    Views
    7,235

    Your saying leave the metal piece and forget the...

    Your saying leave the metal piece and forget the plastic 'guide" Doug?

    - - - - - - - - - -


    Let's do this one step at a time - first things first, let's get the hardware on correctly;

    1) we...
  21. Replies
    26
    Views
    7,235

    The metal plate behind plastic tube guide was on...

    The metal plate behind plastic tube guide was on backwards. The black track needs to mount to the front of the metal plate and things will reach.

    This is the same orientation;
    4424
  22. Replies
    26
    Views
    7,235

    Do any of these help? Not familiar with a glass...

    Do any of these help? Not familiar with a glass part.

    4420442144224423
  23. Replies
    367
    Views
    389,559

    No spare spares, no. That stuff looks fantastic.

    No spare spares, no. That stuff looks fantastic.
  24. Replies
    367
    Views
    389,559

    [[separator]]

    [[separator]]
  25. Replies
    367
    Views
    389,559

    4398 This was a copper silk. Loved working...

    4398

    This was a copper silk. Loved working with it. Not something readily available anymore. Happens more often than not.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4