Search:

Type: Posts; User: woale

Search: Search took 0.01 seconds.

  1. Replies
    84
    Views
    37,844

    Sticky: Print it with the Morpheus then :D Your personal...

    Print it with the Morpheus then :D
    Your personal copy with smaller teeth is here ;)
  2. Replies
    84
    Views
    37,844

    Sticky: Some programs (like nanoDLP as of current build...

    Some programs (like nanoDLP as of current build 1140, but not CW of course) allow to less cure the solid inner areas of a print... to keep strength, increase membrane life time and prevent...
  3. Replies
    84
    Views
    37,844

    Sticky: The export feature on Onshape allows different...

    The export feature on Onshape allows different formats, but the part(s) need to be selected first. Uploaded STL to Thingiverse and updated post to ease the pain ;)
  4. Replies
    84
    Views
    37,844

    Sticky: Build plate fixture washers

    To avoid the bolt remaining inplace when unscrewing the build plate... another "mod" to the Morpheus: it definitely needs a washer between the build plate fixture :
    1439
  5. Replies
    84
    Views
    37,844

    Sticky: Vatholders

    To avoid vat lifting, I've added a few printable holders to keep the vat in place, download/fork on Onshape from here or on Thingiverse from here :
    1438
    I must admit the parts are hard to keep...
  6. Replies
    84
    Views
    37,844

    Sticky: Very good idea @sukhvir. Note the vat should be...

    Very good idea @sukhvir. Note the vat should be heavy enough, or somehow fixed, to avoid the print sticking to the membrane and lifting the vat ;)
  7. Replies
    84
    Views
    37,844

    Sticky: Maybe look for a longer one. I remember 25cm was...

    Maybe look for a longer one. I remember 25cm was too tight, so I used 75cm I had laying around.
  8. Replies
    84
    Views
    37,844

    Sticky: Like these:...

    Like these: https://www.sparkfun.com/products/10363 standard 3pin wire, but maybe try to find something a bit longer.
    Also an 220 Ohm resistor needs to be soldered on the sensor board, like one of...
  9. Replies
    84
    Views
    37,844

    Sticky: Too bad I haven't got the time to print anything...

    Too bad I haven't got the time to print anything fancy yet since "upgrade" with your mods.... just the endstops in post #6 above ;)
  10. Replies
    84
    Views
    37,844

    Sticky: @sukhvir, best of luck with the campaign. It's...

    @sukhvir, best of luck with the campaign. It's looking promising.

    As for the mods, I've also removed the metal plate from the LCD screen which seem to give more consistent prints. Base layers are...
  11. Replies
    84
    Views
    37,844

    Sticky: Euhm guys, am I missing something? What...

    Euhm guys, am I missing something? What kickstarter are you to run @sukhvir?
  12. Replies
    84
    Views
    37,844

    Sticky: Endstop links added to post #6.

    Endstop links added to post #6.
  13. Replies
    84
    Views
    37,844

    Sticky: Very true ;)

    Very true ;)
  14. Replies
    84
    Views
    37,844

    Sticky: I'm afraid the source isn't accessible :confused:...

    I'm afraid the source isn't accessible :confused: and I don't have any experience in decoding stored code from an arduino.
    By the time I'll get to 33cm height prints, I'll ask TOW for their settings...
  15. Replies
    84
    Views
    37,844

    Sticky: You mean our film isn't PDMS ? Any idea how to...

    You mean our film isn't PDMS ? Any idea how to obtain such PDMS film ? And would this allow continuous printing, like Carbon3D ?
  16. Replies
    84
    Views
    37,844

    Sticky: Z min endstop

    Without much hassle, added an optical endstop (sensor here, and board here) on Z Min to ease the build plate levelling:
    14041407
    This allows the build plate to "home" down via Gcode G28 command...
Results 1 to 16 of 16