Search:

Type: Posts; User: TommyDee

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    14
    Views
    1,705

    The jest is correct in the process you site. The...

    The jest is correct in the process you site. The firmware is not causing the error. This is minimal f/w and slicer f/w calls. 1.05 works fine since it is simply an earlier set.

    There must be...
  2. Replies
    14
    Views
    1,705

    If I remember right, yes, you are replacing their...

    If I remember right, yes, you are replacing their header with a known 3D Systems header. The footer, same thing. M109 is handled differently. It needs to be replaced with an "M104 S<temp> P1"...
  3. Replies
    2
    Views
    31

    The supports are part of the extended build time...

    The supports are part of the extended build time estimate. They are not shown but can add significantly to the overall print throughput.
  4. Replies
    2
    Views
    75

    I think John was looking for a motherboard :p

    I think John was looking for a motherboard :p
  5. Sticky: Often yes, it does. Great news! :p

    Often yes, it does. Great news! :p
  6. Sticky: Looking forward to his reply. I know that...

    Looking forward to his reply. I know that sometimes I get some really scrambled numbers when querying the chip but I never write when I see that. Normally that is from not rebooting the serial...
  7. Sticky: Interesting. It should not do that. Have you...

    Interesting. It should not do that. Have you asked Tomuro what may have happened?
  8. Sticky: I've had a blank chip sent to me once, and they...

    I've had a blank chip sent to me once, and they replaced it promptly as it came from 3DS.
    What is the chip programmed for? You can query the chip with ReCube.
  9. Replies
    0
    Views
    119

    Printing Cube3 files on CubePro

    I've been racking my brain to figure out the easiest way to get PETG in CubePro. The problem is that v1.87 kinda sucks on floor density and general print quality for cosmetic parts. However, it is...
  10. Replies
    147
    Views
    22,747

    Sticky: Keep a close eye on eBay. There tend to be good...

    Keep a close eye on eBay. There tend to be good deals on Cube3 carts from time to time. You just have to beat me to it :p
    Basic going rate should be in the neighborhood of $25-$30.

    I found I...
  11. Replies
    6
    Views
    125

    Way cool! Thanks for sharing that. As you can...

    Way cool! Thanks for sharing that. As you can see, I have my hands full of understanding all those lack-of-definitions in the config files.

    Love to see kids learning cool stuff too!
  12. Amazon has a decent deal on some undersized LokBuild

    While supplies last; LokBuild 295mm x 295mm $17.99 baby blue w/ white grid pattern

    https://www.amazon.com/KudoTech-LokBuild-Surface-295x295mm-Versatile/dp/B077TZW218

    Seems some 12" got cut...
  13. Sticky: And thank you for the feedback! Happy printing...

    And thank you for the feedback! Happy printing pizzabaconator.
  14. Replies
    11
    Views
    230

    Looking better already! :)

    Looking better already! :)
  15. Replies
    9
    Views
    9,699

    Sticky: Welcome to the forum, Drivenes. I got an...

    Welcome to the forum, Drivenes.

    I got an included license for 3D Systems Invent. It is a true parametric modeler and it doesn't cost an insane amount of money, under $100 is my best guess.
    30...
  16. Replies
    6
    Views
    125

    Care to share that web browser for the gcode? ...

    Care to share that web browser for the gcode? The decoder you found is likely the same as I've been using.

    Now here is an interesting challenge beyond the current state:
    The decoder should be...
  17. Sticky: :) sounds like a plan.

    :) sounds like a plan.
  18. Sticky: Welcome to the forum, pizzabaconator. I'd say...

    Welcome to the forum, pizzabaconator.

    I'd say try it and see what the messages are from AVRDUDE. Basically, the batch file command string has to see what is actually there so you can try both...
  19. Replies
    6
    Views
    125

    These are settings in the config files, yes. You...

    These are settings in the config files, yes. You can change them in CubePro. Honeycomb infill is a true wall geometry. So the more area, the more materials.

    I haven't dug into these very deep. ...
  20. Replies
    11
    Views
    230

    I am making the assumption that you can manage...

    I am making the assumption that you can manage the extrusion rate for various extrusion types. CR10 uses Cura or Slicer as a core slicer? Basically, there should be a setting for brims, walls, top...
  21. Replies
    11
    Views
    230

    Does the CR10 have automatic bed leveling tech or...

    Does the CR10 have automatic bed leveling tech or is that a seam on the right side of the cube?

    A little more extrusion on the top and bottom fill might be called for.
    The walls look a lot better...
  22. Thread: Z gap

    by TommyDee
    Replies
    6
    Views
    126

    One thing to consider is that the Z-gap sets the...

    One thing to consider is that the Z-gap sets the zero position of Z.
    Every print adds to this.
    ABS I think is adding 0.22mm and PLA is adding 0.25mm.
    That is why you can gap flush to the...
  23. Replies
    1
    Views
    46

    Welcome to the forum, Slivers. Are you using...

    Welcome to the forum, Slivers.

    Are you using the flexible build plate?
  24. Replies
    4
    Views
    250

    I'm finding that 3 skins manages to hide a lot of...

    I'm finding that 3 skins manages to hide a lot of artifacts. The two notable stripes on the chest are part of the original model.

    - - - - - - - - - -


    Fish Fossilz is one of my favorite...
  25. Thread: Z gap

    by TommyDee
    Replies
    6
    Views
    126

    I've gone up as high as 0.25mm on the gap. A...

    I've gone up as high as 0.25mm on the gap. A standard manila folder seems to do the trick.
    It is a balance between minimal 1st layer deformation/squish and a good solid hold.
    I do use a...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4