Search:

Type: Posts; User: bolsoncerrado

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Why do u care to reply to this spam @Tommy?

    Why do u care to reply to this spam @Tommy?
  2. Replies
    9
    Views
    254

    I'm pretty sure it's possible, as long as you...

    I'm pretty sure it's possible, as long as you have the firmware to go with it.
  3. See if this helps:...

    See if this helps: https://www.dropbox.com/s/7d1bhebmbmooksh/SD%20RAPIDE%20LITE%20200.zip?dl=0
  4. Replies
    4
    Views
    339

    Since there is no heatbed on the Cube3 i wouldnt...

    Since there is no heatbed on the Cube3 i wouldnt be that much concerned.
  5. Replies
    3
    Views
    271

    ?? whats going on here?

    ?? whats going on here?
  6. What temp requirements have this nylon? I hear...

    What temp requirements have this nylon? I hear its the worst filament to fight against humidity so old filament could be a serious issue...
  7. This pic here gave me some dirty ideas HaHaHa :D

    3341


    Perhaps an hybrid we could run the nema outside the cube?
  8. Replies
    202
    Views
    38,682

    Sticky: You mean stock cube3 carts "pre-modified" before...

    You mean stock cube3 carts "pre-modified" before installation?
  9. Replies
    7
    Views
    476

    [ THING ] WOw you already built one? :) YOur review in...

    WOw you already built one? :)

    YOur review in 3, 2, 1...
  10. Did you check the start Gcode as well?

    Did you check the start Gcode as well?
  11. Creality Ender still is a hot cake if you look...

    Creality Ender still is a hot cake if you look for a "cheap chinese printer" but you end up having to tweak it sooner or later...

    It all depends on your budget and how much/how often do you want...
  12. Replies
    4
    Views
    373

    Id do a fresh wiring with brand new endstop just...

    Id do a fresh wiring with brand new endstop just to be completely sure its not a faulty boad and triple check the connectors to the board too...replacing the board will be exhausting.
  13. Replies
    4
    Views
    373

    When you replaced the switches did you replace...

    When you replaced the switches did you replace the wiring too?
  14. Replies
    4
    Views
    1,030

    WIth or without glue?

    WIth or without glue?
  15. Replies
    18
    Views
    6,465

    Fckin' spammer.... :/

    Fckin' spammer.... :/
  16. Replies
    2
    Views
    342

    Did you try their official online store?

    Did you try their official online store?
  17. Are we supposed to ask about Creawesome so we're...

    Are we supposed to ask about Creawesome so we're spammed with it now?

    I'm about to hit the BAN button...
  18. If it was in an Ender, you're in the wrong...

    If it was in an Ender, you're in the wrong subforum then :)
  19. Cube Pro Total Conversion: A step-by-step guide on how to "Open source" it...

    Interesting / Inspiring reading!

    https://dyzedesign.com/2018/09/cube-pro-total-conversion-step-by-step-guide/
  20. Replies
    29
    Views
    2,803

    Sticky: You may want to start a new thread with the tool...

    You may want to start a new thread with the tool and instructions on the first post? :D
  21. THe only one i know of that permanently changes...

    THe only one i know of that permanently changes slightly is the wooden infused filament because it actually "overburns" the wood particles inside...
  22. Replies
    4
    Views
    496

    you should try to rotate the piece to rest flat...

    you should try to rotate the piece to rest flat on one side... Yes, fdm can be time consuming if you don't place the pieces and settings correctly.
  23. Replies
    6
    Views
    547

    Interesting findings indeed.... Yet more buggy...

    Interesting findings indeed.... Yet more buggy over and over! Misslabeled software options? hehe
  24. Replies
    11
    Views
    1,036

    How curious, either you're using very few top...

    How curious, either you're using very few top layers or it's underextruding on those cubes! :???
  25. Replies
    11
    Views
    1,036

    Yeah maybe it's misscalibrated and...

    Yeah maybe it's misscalibrated and overextruding...
    https://www.google.es/search?q=calibrating+extrusion&oq=calibrating+extrusion&aqs=chrome..69i57j0l5.3188j0j4&sourceid=chrome&ie=UTF-8
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4