Search:

Type: Posts; User: TommyDee

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    207
    Views
    8,658

    Aha, that is why it appeared to work when I...

    Aha, that is why it appeared to work when I recompiled one and did the hex-edit to get the last characters back. This was simply de- and re-coding. But when I made a change, it didn't work.
  2. Replies
    207
    Views
    8,658

    These are driver configs for the slicer and...

    These are driver configs for the slicer and cubeprint app. Think of the slicer config as a canned set of recipes. Tweaking those recipes will change slicer behavior.

    These files are located...
  3. Replies
    53
    Views
    6,570

    [ HOW TO ] And you are now the owner of a -Limited Release-...

    And you are now the owner of a -Limited Release- ReCube Wand with a number guaranteed to be less than... lets see... 85 at the moment... plus a few early sales and let me remember... oh yea, a few...
  4. Thread: Anet A8

    by TommyDee
    Replies
    11
    Views
    75

    Just reload XP ;) Kidding! It could just be a...

    Just reload XP ;) Kidding! It could just be a bug. It appears to be defining a void. I've heard of insane features like that, but to have one stuck doesn't make sense. These fall into options in...
  5. Thread: Anet A8

    by TommyDee
    Replies
    11
    Views
    75

    Cura's known for quirks.

    Cura's known for quirks.
  6. Thread: Anet A8

    by TommyDee
    Replies
    11
    Views
    75

    It looks like your top layers are working but you...

    It looks like your top layers are working but you have a bigger problem on the bottom. Something is voiding the area inside the robot if you look at the start of the infill. It only starts at some...
  7. Thread: Anet A8

    by TommyDee
    Replies
    11
    Views
    75

    When you slice "marvin", does he have closed...

    When you slice "marvin", does he have closed feet?

    - - - - - - - - - -

    Looking at Cura 3.6, I see an entry of Top/Bottom Thickness, Bottom Thickness, and Bottom Layers all under Shell in basic...
  8. Thread: Anet A8

    by TommyDee
    Replies
    11
    Views
    75

    I think Cura is getting bigger than their...

    I think Cura is getting bigger than their britches. You shouldn't have to tell a slicer to make a skin on top and bottom, only how many layers you want for that skin.

    Most of these programs now...
  9. Thread: Anet A8

    by TommyDee
    Replies
    11
    Views
    75

    Welcome to the forum Neil. Your preview...

    Welcome to the forum Neil.

    Your preview should show what you should be getting. Seems a setting of 'zero top or bottom layer' is set somewhere.
    Cura has a lot of options. It may take a while...
  10. Replies
    207
    Views
    8,658

    There are? We might be talking different files.

    There are? We might be talking different files.
  11. Replies
    207
    Views
    8,658

    Oh, you are thinking a different XML editor? I...

    Oh, you are thinking a different XML editor? I was thinking the config XML files such as Build_Config_Cube_3.xml. We can decode them but not recode them. And that is only due to the header and...
  12. Replies
    207
    Views
    8,658

    That will be sweet! That will certainly be the...

    That will be sweet! That will certainly be the next phase for both Cube3 and CubePro.
  13. Replies
    207
    Views
    8,658

    Thank you once again for your diligent work...

    Thank you once again for your diligent work Buddy! :cool:
  14. Replies
    53
    Views
    6,570

    [ HOW TO ] Any pre-drilled project board will work. Trim up...

    Any pre-drilled project board will work. Trim up the edges to the size you want.
    On eBay, search "prototype board PCB"

    - - - - - - - - - -

    I wanted to make the announcement that the sales of...
  15. Replies
    7
    Views
    108

    Now there is a trick... a small fan and a light...

    Now there is a trick... a small fan and a light bulb should work nicely :)
  16. Replies
    7
    Views
    108

    In that case it is simply reporting that the...

    In that case it is simply reporting that the chamber took too long to heat up. Can you get to the wires for the heater leads? I'm thinking to take an ohm meter to the heater coils to see if they...
  17. Replies
    7
    Views
    108

    ...and the system complains that the chamber temp...

    ...and the system complains that the chamber temp is not going up or reaching temp. I do not know the entire circuit but there may be a thermal reset switch. We've had a discussion on this heater...
  18. Thread: I'm back!

    by TommyDee
    Replies
    4
    Views
    51

    Do I need oxygen? :rolleyes:

    Do I need oxygen? :rolleyes:
  19. Thread: I'm back!

    by TommyDee
    Replies
    4
    Views
    51

    Nice mod there Jack!

    Nice mod there Jack!
  20. Replies
    7
    Views
    108

    Is the fan blowing? Is the heater heating up? ...

    Is the fan blowing? Is the heater heating up? That would be the only other two functions.
  21. Replies
    5
    Views
    57

    Happy Printing Frankthy :) Thanks for report...

    Happy Printing Frankthy :) Thanks for report back.
  22. Replies
    5
    Views
    57

    You might be able to bypass this fuse at the...

    You might be able to bypass this fuse at the connector of the consolidation PCB.
  23. Replies
    5
    Views
    57

    Are you talking about the wire going into the...

    Are you talking about the wire going into the gray ceramic at the end of the nozzle or the little bulb stuffed in between the fins?

    Recently someone made it clear that the little bulb in the fins...
  24. Thread: Filament Deal

    by TommyDee
    Replies
    4
    Views
    87

    We appreciate your helpfulness no less buddy :)

    We appreciate your helpfulness no less buddy :)
  25. Thread: Filament Deal

    by TommyDee
    Replies
    4
    Views
    87

    I think Buddy decided to buy up the lot :p

    I think Buddy decided to buy up the lot :p
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4