Search:

Type: Posts; User: dwhttnbrg

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    72

    Cube for sale

    Selling one of my Cube 3 printers. It is hacked, and setup with the KISS feed system. I have also done the modification to the print head. It runs great with Hatchbox filament, and Supply 3D. I am...
  2. Replies
    58
    Views
    3,568

    Sticky: Selling one of my Cube 3 printers. It is hacked,...

    Selling one of my Cube 3 printers. It is hacked, and setup with the KISS feed system. I have also done the modification to the print head. It runs great with Hatchbox filament, and Supply 3D. I am...
  3. Replies
    58
    Views
    3,108

    [ HOW TO ] I have some PLA that is really soft, If I run it...

    I have some PLA that is really soft, If I run it at 210, it prints for awhile, then seems to bind a bit, and the drive strips it, and it quits feeding. Used 2.0 to modify it. I left the first layer...
  4. Replies
    105
    Views
    6,747

    [ THING ] I actually modified mine to a hard fitting. I...

    I actually modified mine to a hard fitting. I drilled out the bottom of the Push To Connect so the internal tubing will come up into the fitting and flush against the 4mm tubing inside the fitting.
  5. Replies
    9
    Views
    432

    I tried to rethread it. I got it on, but you have...

    I tried to rethread it. I got it on, but you have to push real hard to get the filament past the nut. I was looking for some spares to work with while I retry the process
  6. Replies
    9
    Views
    432

    2222This is the hose from the hot end. The...

    2222This is the hose from the hot end. The discolored part goes into the metal, and there is a space in the plastic to lock the metal bulb, just like in the feed area
  7. Replies
    9
    Views
    432

    I don't use the nut, I use the original hose from...

    I don't use the nut, I use the original hose from the hotbed with a push connector to connect it.
  8. Replies
    9
    Views
    432

    I have a couple jacked up hot ends. I was looking...

    I have a couple jacked up hot ends. I was looking to finish a couple more mods without buying new carts. I was upgrading to a new connector, and tore the small hose in the head, now its to short...
  9. Replies
    9
    Views
    432

    I need some Finished cartridges

    I don't care if the chips are done or not. I would prefer at least one ABS, but I mostly need them for the hot ends. I will buy them and pay shipping, just tell me what you have.
  10. Replies
    105
    Views
    6,747

    [ THING ] The hole is slightly bigger than the tubing, its...

    The hole is slightly bigger than the tubing, its a snug fit.
  11. Replies
    105
    Views
    6,747

    [ THING ] No, I used the drill block that was on here.

    No, I used the drill block that was on here.
  12. Replies
    105
    Views
    6,747

    [ THING ] Yes Sir, just open it up and slide it back and...

    Yes Sir, just open it up and slide it back and cut it where it meets the ridged part. the remove the hot end and drill. Once the hole is there, reinstall the hot end as normal and pull the pipe...
  13. Replies
    105
    Views
    6,747

    [ THING ] 2181This is what I used. The tubing connected to...

    2181This is what I used. The tubing connected to the nozzle was cut at the end where it connected to the cartridge. I then pulled it up through the drilled hole and connected it with the festo...
  14. Replies
    105
    Views
    6,747

    [ THING ] I did this, but pulled the tubing from inside the...

    I did this, but pulled the tubing from inside the hot end out through the hole. I then used a Festo 3mm to 3mm push connector and connected the 2 pieces of tubing. WORKS GREAT!
  15. [ THING ] Corrected the holder, seems to be a little better...

    Corrected the holder, seems to be a little better now. I have printed for 6 hours without any issues.
  16. Replies
    2
    Views
    455

    Nothing wrong, Just curious. Want to see how...

    Nothing wrong, Just curious. Want to see how others are running them, software, tweaks etc
  17. Replies
    2
    Views
    455

    Anyone own a Solidoodle 3?

    Just curious if anyone else has one of these.
  18. [ THING ] I have 3mm OD tubing. I just swapped from a piece...

    I have 3mm OD tubing. I just swapped from a piece of PTFE to some thicker walled stuff. Here is what I currently have going. 21752176

    - - - - - - - - - -

    no, you can watch it pushing it the...
  19. [ THING ] I am also having issues with the filament pushing...

    I am also having issues with the filament pushing the PTFE tubing out of the fitting after 30 min or so of printing.
  20. [ THING ] I am using little screws. What size are the...

    I am using little screws. What size are the screws for the big holes?
  21. [ THING ] Have mine printed and working, but it seems to be...

    Have mine printed and working, but it seems to be pushing really hard against the fitting. Anyone else notice this. Worried about it breaking with just the 2 screws in the front.
  22. Replies
    1
    Views
    212

    It's Alive!!!!

    2127Finished the mod to a degree. I need a better spring, this is one I had, but it's to big for the loop. It stays in place like it is until I can get the right one.
  23. Replies
    4
    Views
    363

    Working on the replacement now. Flameless torch??...

    Working on the replacement now. Flameless torch?? Light the electric lighters??
  24. Replies
    4
    Views
    363

    Bulk Filament Spider Webs

    I have noticed that I am having "spider web" issues with my bulk PLA. Is there a way to back the temp off just a bit? Its not a terrible thing, and a bit of sanding usually gets rid of them. Just...
Results 1 to 24 of 24