Search:

Type: Posts; User: JohnTee

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. R o t f l !!!

    R o t f l !!!
  2. Good point. Maybe they installed a tiny squirrel...

    Good point.
    Maybe they installed a tiny squirrel in there that turns the shaft with it's teeth?
    If so, mine is in bad need of some dental work!

    ----------------
    BTW, the temperatures are spot...
  3. It gets weirder... When i switched build...

    It gets weirder...

    When i switched build plates, it began to print.
    The one I was using at first was kind of rough, with nozzle dents and grooves from improper Z-gaps. I cleaned and sanded it,...
  4. I did swap out the motherboard, as the original...

    I did swap out the motherboard, as the original was broken. This is the first time I've tried to use it since the swap.
    I am using the same power supply that works with the other two printers.
    If I...
  5. I did swap out the motherboard, as the original...

    I did swap out the motherboard, as the original was broken. This is the first time I've tried to use it since the swap.
    I am using the same power supply that works with the other two printers.
    I...
  6. Thanks, Tom. Since there is nothing in the...

    Thanks, Tom.

    Since there is nothing in the filament path to stop it you have two choices. Extruder clogging or filament motor driver weakness.
    -- I am leaning toward motor weakness. Does...
  7. Do stepper motors get tired and weak with old age??

    I'm working on getting a Cube3/Ekocycle printer going. I had to replace the motherboard -- thanks to help from geofreitag -- to get it working.

    Now, when I try to print, it seems that it cannot...
  8. FWIW, I took a shot at installing CubePrint under...

    FWIW, I took a shot at installing CubePrint under Wine on Linux Mint a while back. As best I remember, I hit a dead end when it insisted it needed a certain version of Internet Explorer (10, I...
  9. Replies
    34
    Views
    11,193

    Brilliant! Didn't think of that, and if I had I...

    Brilliant!
    Didn't think of that, and if I had I would've thought it wouldn't work!

    Nice to be printing again, after a hiatus due to busyness.
  10. Replies
    34
    Views
    11,193

    Good suggestion. Turns out, I had made a bad...

    Good suggestion.

    Turns out, I had made a bad ASSumption about the encoder version buddybu included in the tools folder.
    (Long story follows - skip to end if helpful...)
    I copied the...
  11. Replies
    34
    Views
    11,193

    I'm now having a Windows problem with...

    I'm now having a Windows problem with cube3-encoder on Windows 7 Pro (with September updates.)

    It throws an Error Dialog =
    "The application was unable to start correctly (0x000007b). Click OK to...
  12. Replies
    211
    Views
    12,871

    This obviously is not his first rodeo!! ;)

    This obviously is not his first rodeo!! ;)
  13. Replies
    211
    Views
    12,871

    Got it. That is one nice piece of work, bb! ...

    Got it. That is one nice piece of work, bb!

    Kudos to you, and to TD for all the ideas and info.

    Future tweak - could the Printer Model be a pull-down list?
    If so, then perhaps on selection...
  14. Replies
    211
    Views
    12,871

    Can I play?? Where do I find the current...

    Can I play??

    Where do I find the current version?
    Are they at the links in Post #1?
  15. Oops, nothing of interest here, move on.

    Oops, nothing of interest here, move on.
  16. Replies
    264
    Views
    49,498

    @TD My printers never connect to the Internet (I...

    @TD
    My printers never connect to the Internet (I use a standalone wifi if I want to see what it is doing or use the M$ driver), so I have never seen the message you allude to. My bad for not knowing...
  17. Replies
    264
    Views
    49,498

    Ok, here goes... This may turn out to be like...

    Ok, here goes... This may turn out to be like auto forum oil wars, or motorcycle tire wars, but we plunge in.

    Given that (a) you can easily convert one to the other with a simple firmware reload;...
  18. Replies
    5
    Views
    444

    Question: How do you grip the nozzle without...

    Question:
    How do you grip the nozzle without deforming it?

    (I'll bet you have already built a tool for this! :)
  19. Replies
    53
    Views
    8,766

    [ HOW TO ] Yes. With Recube Pro you can set % to any value,...

    Yes.
    With Recube Pro you can set % to any value, from 0 to 100.
    I always set my chips to 97%, because it's prime. :cool:
  20. Edit 8/19: Humph! As usual, you thought of...

    Edit 8/19:

    Humph!

    As usual, you thought of things that would never have occurred to me!! http://www.print3dforum.com/images/smilies/rolleyes.png

    Thanks for the insight.
    -----------------
    ...
  21. Question: Does the Cube 3 firmware do anything...

    Question: Does the Cube 3 firmware do anything differently for an ABS cartridge vs a PLA cartridge?
    Is there any reason why I can't wire a chip permanently to the contacts, and therefore not need...
  22. FWIW - A workaround for adding something before...

    FWIW - A workaround for adding something before someone else has replied to your post is to edit your post and add the new stuff after a line of dashes.

    ------------------------------
    Like this!...
  23. Replies
    7
    Views
    748

    Aha, I see. Nice! The battery case example looks...

    Aha, I see. Nice!
    The battery case example looks as if you used little rectangular holes.
    I wonder how small you could make the holes so Cube Print would still honor them?
    Could they be small...
  24. Replies
    7
    Views
    748

    @TommyDee - Could you please elaborate a little...

    @TommyDee -
    Could you please elaborate a little on "microholes"?

    Does this mean to design small diameter holes thru thin walls?
    What diameter works well?
    How closely spaced?
    Why does this...
  25. ...but you are still welcome to be here!! :)

    ...but you are still welcome to be here!!
    :)
Results 1 to 25 of 184
Page 1 of 8 1 2 3 4