Search:

Type: Posts; User: TommyDee

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    24
    Views
    7,959

    Sticky: Hey Tarer1an. You got bit by the bug huh ;] ...

    Hey Tarer1an. You got bit by the bug huh ;] Glad to see your are having a good time with these. Nice catch on the buy resin of printer. Would love to know how it does. Also that snap unit......
  2. Replies
    1
    Views
    3,620

    Sticky: Minimum CubePro File set v2.02 -...

    Minimum CubePro File set v2.02 - GoogleDriveDownload
  3. Replies
    3
    Views
    84

    Retraction makes noise but that is normal. Once...

    Retraction makes noise but that is normal. Once the filament is flowing properly, you will know it.

    Please tell me what you are using for filament.
  4. Replies
    3
    Views
    84

    You are not flowing filament at the proper rate. ...

    You are not flowing filament at the proper rate. With Cube3, that means there is a clog in the nozzle.

    When the print runs, do you hear clicky sounds? If you this is the case, the filament...
  5. Replies
    154
    Views
    27,606

    Buddy... the images aren't images.

    Buddy... the images aren't images.
  6. Replies
    2
    Views
    101

    You might need the chamber heater for the printer...

    You might need the chamber heater for the printer to start. There is chamber temp sensing IIRC. And yes, they are AC heaters with a thermal cutoff switch.
  7. Replies
    154
    Views
    27,606

    That is the most unique and clean implementation...

    That is the most unique and clean implementation I've seen on any repurpose to date. 4 years well spent! Great vision.
  8. Replies
    154
    Views
    27,606

    Did I miss a screen swap somewhere?

    Did I miss a screen swap somewhere?
  9. Replies
    154
    Views
    27,606

    I did indeed! Love those little fixers ;]

    I did indeed! Love those little fixers ;]
  10. Replies
    154
    Views
    27,606

    Bravo Kiza! That is above and beyond awesomeness!

    Bravo Kiza! That is above and beyond awesomeness!
  11. Replies
    24
    Views
    7,959

    Sticky: http://www.print3dforum.com/showthread.php/3024-3D...

    http://www.print3dforum.com/showthread.php/3024-3DS-Cube-File-Links?p=50599&viewfull=1#post50599
  12. Replies
    130
    Views
    39,359

    [ HOW TO ] Read through the thread of my build RicciEU. ...

    Read through the thread of my build RicciEU. When you get to the part about 'you can do this is a NANO and 2.2K resistor', stop and realize I was no different than you taking on this challenge. The...
  13. Replies
    9
    Views
    654

    RicciEU, Cubify, the code that drives all the...

    RicciEU, Cubify, the code that drives all the prosumer 3DS printers, is a canned program. This means all recipes are created and fixed based on the material chip presented. There are external...
  14. Replies
    154
    Views
    27,606

    ^that!

    ^that!
  15. Replies
    14
    Views
    3,037

    Great stuff Doug. I wish I had time to put into...

    Great stuff Doug. I wish I had time to put into S3D.

    The take-away is that CubePro is backwards compatible with older file types. CubePro 2.02 operates on a whole different level than the...
  16. Replies
    3
    Views
    266

    Definitely the nozzle end ;]

    Definitely the nozzle end ;]
  17. Replies
    3
    Views
    266

    First maintenance after 3Kg of PETG

    4112

    I've been running NovaMaker white PETG almost exclusively for the last 3 spools.

    Yesterday I was getting some clicking. This is what I found - the 42mm tube was nearly completely...
  18. Replies
    6
    Views
    395

    That is great Arcadium. One cartridge will be...

    That is great Arcadium. One cartridge will be sufficient. Be sure to apply the modified f/w to keep you chip from counting down if it has a usable percentage left.
  19. Replies
    6
    Views
    395

    I've run a pen-spring before.

    I've run a pen-spring before.
  20. Replies
    9
    Views
    654

    If you back up to V1.87, you can modify the files...

    If you back up to V1.87, you can modify the files for CubePro. There you can set the temperatures. PETG seems to want about 10-15 degrees less than Cubify ABS. I set the temp to 250C in Cube3. ...
  21. Replies
    6
    Views
    395

    Good point buddybu. A nozzle and chip can ship...

    Good point buddybu. A nozzle and chip can ship in an envelope if you separate the push-nut.
  22. Replies
    154
    Views
    27,606

    Now that is some serious integration!

    Now that is some serious integration!
  23. Replies
    4
    Views
    623

    Interesting. I don't know enough about the code...

    Interesting. I don't know enough about the code to know how that could be.
  24. Replies
    4
    Views
    623

    Are you at the edge of the microprocessor's...

    Are you at the edge of the microprocessor's memory?
  25. Replies
    154
    Views
    27,606

    Very nice wire dressing!

    Very nice wire dressing!
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4