Search:

That looks overcured to me. I have mine running at 12 seconds per layer and get perfect results.

Nice one bolsoncerrado. How much did you pay for the replacement screen? Or did they just send a replacement? Has anyone managed to get hold of the kit to upgrade their Morpheus? I'm not getting much...

http://www.materialise.com/en/software/magics

I think you can download a demo, however full version is for professional level printers (those costing £30k+) and software costs around $20k

A few points to note here Karthik:

- Your supports are too thick. They will damage the part when you remove them.
- This part only needs support on the securing flaps. The base should be sitting...

Hi Karthik,

Why have you added the ribs? Are they part of the final print, or are they supports to help the print?

Hi Karthik,

Can you please send me the stl file so I can see how it should look? I can recommend supports after looking at it.

Hi Karthik. Not sure what you mean by accuracy, but print sizes are as I expect them to be, as long asI increase the model size by 0.4% to compensate for shrinkage. with regards to cleaning the build...

I've not used a printer with PDMS coating, however I assume that the peeling process is a bit better with the PDMS coating. The difference comes down to cost. The film layer on the Morpheus will last...

Nice one Karthik and good to see you are on your way to making some good prints. Some good tips there from mojor also. I would suggest the following:

- The largest area should be in contact with...

Does your laptop not have HDMI? Not sure why you would want to use DVI to VGA. I don't think an analogue VGA signal will be as clean as a digital one. Try DVI to DVI or HDMI to HDMI.

Hi folks. All seems quiet on the Morpheus forum front. Anyone printed anything they would like to share? :)

Also, I've learned a bit more about how to successfully print larger items / print in...

Hi Knibor. I'm interested in trying this on the Pi. Any chance you could write a few brief lines of how you set it up? Just want to see if it is worth trying. How are you getting on with your...

Have you tried it?

Hi acnow. Can you please share the problem (and solution) of your broken monitor?

You will need to email FTD for all that info Karthik. We are all hobbyists here and not Chemical Engineers I'm afraid.

Not tried it myself but don't see why it shouldn't do 25 micron layer height. It ways on their website that the resin can achieve 0.02mm layer height

Hi Karthik. The resin I have been using is FTD (FunToDo). I'm not sure if they have distributors in India though. You will also possibly get 25 microns from the OWL resin, which they will release...

@bolsoncerrado that isn't one of my prints, but is a screenshot I found which gave me a better idea of supports to use. If the model in the picture is hollow, it should print fine, otherwise the...

Hi @acnow. Sorry for the delayed response, but I have attached a screenshot of my Morpheus configuration (for FTD snow white resin). For meshmixer, I found the following screenshot helpful, but to be...

Great idea @bolsoncerrado. I've never done one before but will have a bash.

Hi all and sorry @AngryPanda for late reply. We have our Kickstarter campaign kicking off next week so have been really busy getting things in place for that.

My dual vat system is ready to run...

Looking good. I've been busy over the past few weeks getting our Kickstarter campaign ready but will come back to finish my dual vat system shortly.

By the way @AngryPanda, the vat lockdown system...

Wow. That's a long and very informative post @angrypanda and there are things we can all learn from it. Congratulations and well done on your successful prints. Looks like we are starting to break...

I think people have been printing successfully but just haven't shared. Have you any prints of your own @acnow you could upload?

Work in progress. Hopefully should start printing next week :D

1448