Search:

Type: Posts; User: ztoddman1

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    355
    Views
    37,907

    Do some searching, there is some hacked versions...

    Do some searching, there is some hacked versions floating around the net for S3D.
  2. Replies
    14
    Views
    1,876

    Nice. I likey it. I have an MK8 on the way so...

    Nice. I likey it.
    I have an MK8 on the way so next time my original gear fails for some reason, I may have to give this a try. Luckily I have a 2 junker printers and 1 that is being unused so........
  3. Replies
    14
    Views
    1,876

    Beat me to that question TD! - - - - - - - - -...

    Beat me to that question TD!

    - - - - - - - - - -


    TD, could something be designed to utilize the 2 screws on either side?
  4. Replies
    14
    Views
    1,876

    Welcome Yordibas! Would love to see movie details...

    Welcome Yordibas! Would love to see movie details of your tasty MK8 model. Do tell!!
  5. Replies
    14
    Views
    1,876

    R81- could you do a close up on your design?

    R81- could you do a close up on your design?
  6. Replies
    7
    Views
    3,539

    I have the electronics out and can easily get to...

    I have the electronics out and can easily get to them. I can take any photos you want
  7. Replies
    43
    Views
    4,677

    The only thing I see that would pose an issue is...

    The only thing I see that would pose an issue is the sharp curves from the spool roll, out of the container, and into the drive. When you get toward the end of the filament, I find it gets brittle...
  8. I have 2 tubes of the glue if anyone wants them....

    I have 2 tubes of the glue if anyone wants them. Just pay the 8.00 shipping and have at it. 1 is about 75% full and the other 60%.
  9. Replies
    23
    Views
    1,960

    I am batting .500 with craigslist luck. 1 works...

    I am batting .500 with craigslist luck. 1 works perfectly, 1% used on either cartridges and the other, hot end carriage busted. My advice, pass, use that 75.00 for a new on eBay like TD suggested.
  10. I use an overture build plate that came with the...

    I use an overture build plate that came with the filament. NEver once have I put any glue on it or tape and it sticks fantastic. Best build plate thus far!
  11. Replies
    302
    Views
    88,994

    Sticky: I have one, well, 2. email me at...

    I have one, well, 2. email me at ztoddman1@yahoo.com
  12. Replies
    30
    Views
    4,099

    I just downloaded that earlier today not knowing...

    I just downloaded that earlier today not knowing it was from someone here! Oh as well as the darth vader mask cap(?) Way Cool. THanks!
  13. Replies
    36
    Views
    22,064

    Sticky: [ THING ] your ol pal!

    your ol pal!
  14. Replies
    302
    Views
    88,994

    Sticky: I do, actually, have 2 printers now to part out...

    I do, actually, have 2 printers now to part out with. email me, ztoddman1@yahoo.com
    Thanks Tommy for the heads up, will reach out to you soon.
  15. Replies
    302
    Views
    88,994

    Sticky: I have 2 junker cube 3's. HAte to see them just...

    I have 2 junker cube 3's. HAte to see them just sitting here with perfectly, well, mostly perfectly useable parts. Is anyone out there needing something I could rob off these? I did rob them of the...
  16. Replies
    15
    Views
    2,096

    I had 2 printers, one was my original, it went...

    I had 2 printers, one was my original, it went down, used my spare to attempt to get it back up and running and it failed. Found a used one off marketplace locally I couldnt let it go. I have all...
  17. Replies
    15
    Views
    2,096

    just wait WinterWarg, the fun/thrill has only...

    just wait WinterWarg, the fun/thrill has only just begun. Tommy has contributed soooo much for this little printer that, take ALL his knowledge and bank it. He ROCKS!
  18. Replies
    15
    Views
    2,096

    use TommyDees design. I have had only 1 problem...

    use TommyDees design. I have had only 1 problem with it but it was, uh, user error.
    http://www.print3dforum.com/showthread.php/1278-Universal-Hub
    https://www.thingiverse.com/thing:3804561/files...
  19. Replies
    1
    Views
    612

    cheap cartridge for parts

    not mine just surfing and ran across it.

    https://www.ebay.com/itm/Cube-3D-PLA-Printer-Cartridge-Neon-Green-3D-systems/174111014171?hash=item2889d33d1b:g:BXIAAOSwNd5d4Xfy
  20. Replies
    2
    Views
    729

    and here are some links for new adapters!...

    and here are some links for new adapters!
    https://www.mpja.com/24-Volt-Adapter-Power-Supply-5A-Megmeet/productinfo/32885+PS/ --- Where I got mine!
    ...
  21. Replies
    4
    Views
    887

    that was quick lived

    that was quick lived
  22. Replies
    4
    Views
    1,145

    [ THING ] yes. That is exactly what I had to do. doesn't...

    yes. That is exactly what I had to do. doesn't matter if it is a test print or a regular file, just as long as it is not an enormous file to deplete the filament, just get it below 100 and obviously...
  23. I use a purple Elmer's glue stick, never has it...

    I use a purple Elmer's glue stick, never has it dried while processing and doing its thing. would be interesting to see what the culprit is. if Tommy's on the case, by God it will get solved!
  24. I have to agree, that first layer is screwy. I've...

    I have to agree, that first layer is screwy. I've had a similar issue but my issue was a design flaw. Had a leg in the design which made the entire design sit higher and not flush on the bed.
  25. Ive done all 3 of the hubs, the hubcap is the...

    Ive done all 3 of the hubs, the hubcap is the most bulkiest but the wings seem to break a lot, just started using the B2B and thus far no issues. My favorite is a version of the KISS one that TD...
Results 1 to 25 of 149
Page 1 of 6 1 2 3 4