Search:

Type: Posts; User: MegaloDon

Page 1 of 19 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    13

    You can use another USB stick as long as it is...

    You can use another USB stick as long as it is formatted FAT32.

    As far as the Cube Toolbox, it only works in Windows. You will need to get the file already hacked.

    - - - - - - - - - -

    Here...
  2. Replies
    8
    Views
    94

    Here is a good reference to tear it down....

    Here is a good reference to tear it down.
    https://openbuilds.com/threads/tear-down-of-cubify-cube-3-3d-printer-convert-to-reprap.5689/
  3. Replies
    8
    Views
    94

    Check to see if the belt is connected to the...

    Check to see if the belt is connected to the print head. There is a common problem where one or both of the set screws on the head have cracked the plastic housing. My friend had this issue and it...
  4. Replies
    64
    Views
    6,029

    Sticky: I don't think you need the rinse away chip. The...

    I don't think you need the rinse away chip. The only way Cube Print software will let you use it is with supports generated from its own software. So you can't make your own supports and tell it to...
  5. Replies
    109
    Views
    10,215

    [ THING ] I know what you mean. I used to have CRS (can't...

    I know what you mean. I used to have CRS (can't remember sh!t) but it has progressed to CRAFT (can't remember a f'ing thing). :confused:
  6. Replies
    109
    Views
    10,215

    [ THING ] http://www.print3dforum.com/showthread.php/1075-(B...

    http://www.print3dforum.com/showthread.php/1075-(BETA)-Cube3-Printable-Nozzle-Replacement-by-MegaloDon?p=42476&viewfull=1#post42476
  7. Replies
    131
    Views
    11,507

    So I tried printing Taulman Bridge nylon on my...

    So I tried printing Taulman Bridge nylon on my Cube 3 and it works quite well. I didn't even need to use a 3rd party slicer. Just used Cube Print software and set it to ABS. Taulman Bridge prints...
  8. Replies
    72
    Views
    3,008

    It has already been shared here. >>> ...

    It has already been shared here. >>> http://www.print3dforum.com/showthread.php/1075-(BETA)-Cube3-Printable-Nozzle-Replacement-by-MegaloDon?p=42476&viewfull=1#post42476

    Just print it in ABS and...
  9. Replies
    72
    Views
    3,008

    If you are referring to the one I made, it and...

    If you are referring to the one I made, it and the one that Bo is printing (also designed by me) both have the same tolerances. I have been using a couple I printed in ABS since I first designed it...
  10. Replies
    72
    Views
    3,008

    I don't see any way to make the walls thicker...

    I don't see any way to make the walls thicker unless you eliminate the push nut. As is, the outside has to be a certain size to fit in the printer, and the inside has to be big enough to accommodate...
  11. Absolutely not. It will more than quadruple the...

    Absolutely not. It will more than quadruple the time (unless you are only telling it to print from one nozzle). It has to clean the nozzle on each tool change.

    As far as the chips, the color...
  12. Replies
    4
    Views
    116

    The Cube 3 will. Cube Print software won't.

    The Cube 3 will. Cube Print software won't.
  13. Replies
    2
    Views
    83

    It's caused by Cube Print software. This happens...

    It's caused by Cube Print software. This happens on a lot of prints that have a small area. The only time it doesn't happen is if you design it to an exact size that corresponds to the layer...
  14. Replies
    22
    Views
    2,342

    I wouldn't worry about resurrecting old threads. ...

    I wouldn't worry about resurrecting old threads. Just because they haven't been posted in for a while doesn't mean they are not still valid.

    And welcome to the forum!
  15. Here is the one I designed for Bo....

    Here is the one I designed for Bo.
    https://drive.google.com/open?id=1vBqYWb-UN22HfyHzAHI5lvAZ7bLteTLr

    There are 2 versions. One has a raft / brim, and a blob shield (ideally designed for...
  16. Bo, do you think the magnet cap I designed for...

    Bo, do you think the magnet cap I designed for you would help in this situation?
  17. Thread: HubCap V1

    by MegaloDon
    Replies
    57
    Views
    1,768

    [ THING ] I couldn't find the damn post either! :rolleyes:...

    I couldn't find the damn post either! :rolleyes:

    But I did find the link to where I ordered mine. :D
    https://ultimate3dprintingstore.com/products/nema-17-hybrid-step-motor-17pm-k374bn01cn

    -...
  18. Replies
    296
    Views
    49,453

    Sticky: My understanding was the only change made to the...

    My understanding was the only change made to the firmware was that it blocks writing to the chip.
  19. [ THING ] Tried that. Doesn't move at all.

    Tried that. Doesn't move at all.
  20. [ THING ] I couldn't make a print file for unloading...

    I couldn't make a print file for unloading because I couldn't figure out how to make it run backwards. Believe me, I tried.

    When it pauses, put the filament in before you hit resume. I don't...
  21. Replies
    10
    Views
    327

    190 seems kind of low for PLA. But I suppose...

    190 seems kind of low for PLA. But I suppose some filaments might go lower. The reason why I said it seems too hot is that when it is too hot it will cause stringing and drooping. You clearly have...
  22. Replies
    10
    Views
    327

    It uses the settings from the .cube3 file.

    It uses the settings from the .cube3 file.
  23. Replies
    10
    Views
    327

    Looks like it may be too hot for the filament you...

    Looks like it may be too hot for the filament you are using.
  24. Replies
    4
    Views
    382

    2431 Ok, 90 is one thing but printing in mid...

    2431

    Ok, 90 is one thing but printing in mid air? This is what happened when my supports failed. It somehow recovered.

    Too funny. :D
  25. Replies
    5
    Views
    1,129

    Ok, so I have recently been getting T14 errors...

    Ok, so I have recently been getting T14 errors while trying to print ABS. It wouldn't even start to print before getting the error. I always only have 1 print head in place because I really don't...
Results 1 to 25 of 453
Page 1 of 19 1 2 3 4