Search:

Type: Posts; User: bolsoncerrado

Search: Search took 0.02 seconds.

  1. Same boat here, still awaiting TOW response for...

    Same boat here, still awaiting TOW response for the last MONTHS :(

    Keep me posted if you hear from them. However mine didnt came from a leakage.

    I suspect we were booked with faulty LCD panels...
  2. @karthik.pdy where did you get the morpheus...

    @karthik.pdy where did you get the morpheus resin? at which price?
  3. Yikes! Perhaps a problem with the mosfet? Did you...

    Yikes! Perhaps a problem with the mosfet? Did you check wiring inside the printer?
  4. Did you try a different computer? different USB...

    Did you try a different computer? different USB cable? different USB port?
  5. I used a cutter knife blade to carefully peel it...

    I used a cutter knife blade to carefully peel it from the monitor...
  6. Best of lucks with that, @sukhvir! You should...

    Best of lucks with that, @sukhvir!

    You should program a Thunderclap for it too :D
  7. Definetly, nth times better than a laptop+CWS...

    Definetly, nth times better than a laptop+CWS combo!!

    You dont burn a laptop display + computer cycles + having to loose a computer as it has to remain untouched as the print goes
    You can put the...
  8. yeah after a given amount of minutes, 2 or 3, you...

    yeah after a given amount of minutes, 2 or 3, you no longer get input from the pi hdmi no matter what. sometimes not even after fresh boot up.

    I'm printing now from pi2 eversince and hassle free....
  9. @sukhvir I had to move nanodlp SD card to a...

    @sukhvir I had to move nanodlp SD card to a Raspi2 as I had HDMI issues with a Raspi3 with 6 HDMI cables I tested. All of them blanked out after a while. But the one I tested worked fine with the...
  10. Aren't you trying nanodlp yourself sukhvir?

    Aren't you trying nanodlp yourself sukhvir?
  11. Hmmmm now that you mention it, I think I also had...

    Hmmmm now that you mention it, I think I also had antialiasing enabled as per TOW visit... hmmm
  12. Welcome @Brickmaker! I'm also curious on what...

    Welcome @Brickmaker! I'm also curious on what your issue is.
  13. OK TOW to the rescue, it was some sort of unknown...

    OK TOW to the rescue, it was some sort of unknown CWS setting that got changed somehow (?!?!?!) as I never knew there was such menu!

    Under File -> Preferences you can set up a Foreground and...
  14. I tried all sort of reboots, resets,...

    I tried all sort of reboots, resets, reconnections and everything I could think of but no luck yet...
  15. Well just realized its the actual "image" of the...

    Well just realized its the actual "image" of the monitor, ie I can see the slice and if i drag the CWS windows on the "extended desktop" to the Morpheus monitor, I can see thru it, but of course the...
  16. OK today I went to try once more with the FTD...

    OK today I went to try once more with the FTD resin and found out a weird issue!?

    The monitor on the Morpheus is getting fully lit when I launch the print instead of just the section (slice) it's...
  17. The shorter the cable between the computer and...

    The shorter the cable between the computer and the Morpheus the better, and even better if they have ferrite shields in it.
  18. Yes, that might be the issue. Also it could be...

    Yes, that might be the issue. Also it could be faulty USB connections (usb wire, bad USB port) try switching ports and/or wires. Last attempt would be try another computer and same software to...
  19. Check the "Successful prints" thread instead.

    Check the "Successful prints" thread instead.
  20. I'll have to order some Photocentric bottles to...

    I'll have to order some Photocentric bottles to test.... :P
  21. Yes I wonder how can TOW work so fine with MJ+!!!...

    Yes I wonder how can TOW work so fine with MJ+!!! :(

    Photocentric and other daylight / water resins are "non UV" curable, so I wonder why they work "so well" with Morpheus lol
  22. ...and a link to such resin! hehe

    ...and a link to such resin! hehe
  23. I also noticed the "suck up" effect with the FTD...

    I also noticed the "suck up" effect with the FTD resin (not with the MJ+ one) of the VAT towards the plate... I guess we would need to add some pressure manually for the first layers until the...
  24. nanoDLP to the rescue!!! :D Scary stuff,...

    nanoDLP to the rescue!!! :D


    Scary stuff, Angrypanda!

    Indeed a couple simple endstops should do the job and just cut the steppers current. Too weird TOW didnt install them in this version, i...
  25. Yes they explained the trick while they were...

    Yes they explained the trick while they were here.... Only press STOP while printing when the Z moves, so the UV leds are off while Z moves. Then the UV leds will be off if you cancel a print.
    ...
Results 1 to 25 of 25