Search:

Type: Posts; User: sukhvir

Search: Search took 0.00 seconds.

  1. Replies
    75
    Views
    59,426

    I've not used a printer with PDMS coating,...

    I've not used a printer with PDMS coating, however I assume that the peeling process is a bit better with the PDMS coating. The difference comes down to cost. The film layer on the Morpheus will last...
  2. Replies
    75
    Views
    59,426

    Does your laptop not have HDMI? Not sure why you...

    Does your laptop not have HDMI? Not sure why you would want to use DVI to VGA. I don't think an analogue VGA signal will be as clean as a digital one. Try DVI to DVI or HDMI to HDMI.
  3. Replies
    75
    Views
    59,426

    Great idea @bolsoncerrado. I've never done one...

    Great idea @bolsoncerrado. I've never done one before but will have a bash.
  4. Replies
    75
    Views
    59,426

    Hi all and sorry @AngryPanda for late reply. We...

    Hi all and sorry @AngryPanda for late reply. We have our Kickstarter campaign kicking off next week so have been really busy getting things in place for that.

    My dual vat system is ready to run...
  5. Replies
    75
    Views
    59,426

    I set it up a couple of weeks ago @bolsoncerrado,...

    I set it up a couple of weeks ago @bolsoncerrado, however had issues with it displaying layers. I'll give it another go soon, but am currently working on the dual vat build. Is anyone else going to...
  6. Replies
    75
    Views
    59,426

    I don't think the anti-aliasing would cause too...

    I don't think the anti-aliasing would cause too much of a problem - it would just add/remove a few pixels to give a smoother print, however I personally don't think it's worth having on and always...
  7. Replies
    75
    Views
    59,426

    I have moved the above post to the...

    I have moved the above post to the Troubleshooting thread :D
  8. Replies
    75
    Views
    59,426

    @Brickmaker, see my settings attached. I have...

    @Brickmaker, see my settings attached. I have never used anti-aliasing, so I'm not sure if that is part of the issue. Also, put your slide/Tilt value to 0 then click on AutoCalc. Can you put up a...
  9. Replies
    75
    Views
    59,426

    Hi @Brickmaker. Can you be more specific? How...

    Hi @Brickmaker. Can you be more specific? How many layers are you getting to stick to the print bed? Is it only the base layers? Also, the exposure time for FTD resin is 50 seconds for base layers (3...
  10. Replies
    75
    Views
    59,426

    I'm not sure if I had a similar issue, however I...

    I'm not sure if I had a similar issue, however I had mistakenly closed the DLP screen on CW and it ended up sending blanks that didn't cute to the Morpheus. Not sure if I restarted Morpheus or the...
  11. Replies
    75
    Views
    59,426

    I can also confirm that windows 10 works...

    I can also confirm that windows 10 works perfectly well for me. Fortunately, I've not had any software issues thus far.
  12. Replies
    75
    Views
    59,426

    Hi manbogi91. This is not a problem I have come...

    Hi manbogi91. This is not a problem I have come across, however don't think it has anything to do with the Morpheus. It is essentially just acting like a monitor plugged into your computer, so...
  13. Replies
    75
    Views
    59,426

    Thanks for joining the forum and also for your...

    Thanks for joining the forum and also for your update jfornies. I think I had the same problem with my first film where I cleaned it with IPA and it seeped through a minor hole between the films....
Results 1 to 13 of 13