Search:

Type: Posts; User: ercnbal

Search: Search took 0.00 seconds.

  1. Replies
    14
    Views
    20,762

    I've sold the printer due to financal problems. ...

    I've sold the printer due to financal problems.
    I can suggest you to clean the nozzle with a heated paper clip or better more thinner metal.
    The heated metal will melt the filament and stick to...
  2. Replies
    14
    Views
    20,762

    I don't have any PLA chip and I don't want to...

    I don't have any PLA chip and I don't want to print abs :D

    Do you suggest me to use original slicer or is there a good s3d profile?

    Since I have only abs chip, maybe trying to change the...
  3. Replies
    14
    Views
    20,762

    I have tried it many times. I have connected...

    I have tried it many times.
    I have connected Abs chip to reader and printing Pla with s3d profile. I'm not sure but maybe profile can cause the problem. Since I tired to cleaning the extruder and...
  4. Replies
    14
    Views
    20,762

    Actually it was the original ABS. I change the...

    Actually it was the original ABS. I change the filament with an ordinary PLA. Now flow issue is solved but clogging problem is not solved. Beginning of the print there is no problem but after half an...
  5. Replies
    14
    Views
    20,762

    I heated an paperclip and used it to remove the...

    I heated an paperclip and used it to remove the clogged filament. I'm not sure its working well but now at least it can extrude filament :).



    Maybe there exist some particles in the nozzle or I...
  6. Replies
    14
    Views
    20,762

    Thank you for reply TD. I'm not sure to...

    Thank you for reply TD.

    I'm not sure to totally understand you, do you suggest me to disassemble the hotend and nozzle assembly to fix the issue?
  7. Replies
    14
    Views
    20,762

    Hotend & Nozzle Need Help

    Hi everyone, I hope you and your loved ones are all fine.


    I think my nozzle is clogged. I dissambled the extruder and check that gear and pulley can freely rotate. But it is not able to exture...
  8. Replies
    8
    Views
    4,701

    I guess that you solve the issue but I want to...

    I guess that you solve the issue but I want to share the profile which I found, it looks like working.


    I modified its wiping location but I shared the original one because I don't know all...
  9. Replies
    58
    Views
    42,922

    Thanks for your guidance, razor81. Do you...

    Thanks for your guidance, razor81.

    Do you think that going with Bowden setup with the stock cubepro will be a good idea? What might be the difference between core xy and cartesian xy designs?
    ...
  10. Replies
    2
    Views
    2,330

    Yeap, It works perfectly. Thanks for your help...

    Yeap, It works perfectly. Thanks for your help SixNix.
  11. Replies
    2
    Views
    2,330

    Extruder Disassembly

    Hi everyone,

    I want to disassemble extruder motor an aluminium guider since filament is squeezed inside. How can I disassemble the two bolts whose had is damaged?

    If I try to cut o horizontal...
  12. Replies
    10
    Views
    10,242

    Probably you need to follow the lines on the PCB...

    Probably you need to follow the lines on the PCB and search the datasheet of the component on the board. This can be helpful to understand how the sensor sent information. Next step will be...
  13. Replies
    58
    Views
    42,922

    SixNix Thank you so much for trying to help me. I...

    SixNix Thank you so much for trying to help me. I cannot create time for care in my printer for now, I'll be here a month later.

    See you soon print3dforum. :)
  14. Replies
    58
    Views
    42,922

    I agree with you TommyDee. "Modern Firmware" can...

    I agree with you TommyDee. "Modern Firmware" can slow down at the corners, which eliminate the one of the important factor for vibration. When we generate the print file with Simplify3D, does this...
  15. Replies
    16
    Views
    20,919

    :D I couldn't find. May I use the abs cartridges...

    :D I couldn't find. May I use the abs cartridges chip for Pla filament?
  16. Replies
    58
    Views
    42,922

    Can coreXY design help for reducing the effect of...

    Can coreXY design help for reducing the effect of the high inertia?
    https://www.youtube.com/watch?v=_ramiM3KHYE
  17. Replies
    16
    Views
    20,919

    Hi, everyone. I have only one Pla cartridge...

    Hi, everyone.


    I have only one Pla cartridge while 2 abs. Unfortunately half of the chip of the my PLA cartridge is lost. Is there any way to make a PLA chip to use this half :D ?
    3803

    - - -...
  18. Replies
    153
    Views
    521,560

    [ HOW TO ] I'm so grateful for your help TommyDee. Now it's...

    I'm so grateful for your help TommyDee. Now it's working.:)
  19. Replies
    153
    Views
    521,560

    [ HOW TO ] Hi TommyDee "I have build the Tomuro's circuit...

    Hi TommyDee

    "I have build the Tomuro's circuit and I have upload the TommyDee's test program with Arduino software. So far there is no problem program works well."
    My printer came today and I...
  20. Hi TommyDee Can you give more details about...

    Hi TommyDee

    Can you give more details about buddybu's cube editor?
    Also I found that https://groups.google.com/forum/m/#!msg/kisslicer-refugee-camp/ZMuIrtn5Mfo/H2brFz3WXD4J

    İs there anyone...
  21. Replies
    153
    Views
    521,560

    [ HOW TO ] I'm verry happy to get quick answers from you....

    I'm verry happy to get quick answers from you. Please accept my deepest thanks.


    Also, I forgot to mention it yesterday but I changed the 100k ohm resistor with 330 ohm since the button didn't...
  22. Replies
    153
    Views
    521,560

    [ HOW TO ] Hi, I'm new in the forum. When I found this...

    Hi, I'm new in the forum.

    When I found this platfrom, I decided to buy a CubePro. Now it's on the way to come my home.
    I have build the Tomuro's circuit and I have upload the TommyDee's test...
Results 1 to 22 of 23