Search:

Type: Posts; User: Leonardo

Search: Search took 0.00 seconds.

  1. Replies
    12
    Views
    3,832

    [ HOW TO ] First off Tommy, please, could you remove/delete...

    First off Tommy, please, could you remove/delete that dirty post ?

    Getting back on my Cube not seeing the new magnetic surface, reversing it did not work. It is so shiny that the system shows an...
  2. Replies
    12
    Views
    3,832

    [ HOW TO ] Thank you so much Tommy! 1:40 AM here... I will...

    Thank you so much Tommy!
    1:40 AM here... I will do more tests tomorrow and will post the results.
    Have a nice weekend!
  3. Replies
    12
    Views
    3,832

    [ HOW TO ] Tommy, I cannot remove the magnetic plate because...

    Tommy, I cannot remove the magnetic plate because now it is glued to the stock build plate.
    What I was thinking that I can do is reversing the PEI layer so the grainy surface will be facing down....
  4. Replies
    12
    Views
    3,832

    [ HOW TO ] Yes Doug!! No glue, no blue tape, nothing......

    Yes Doug!!
    No glue, no blue tape, nothing... just the bare surface of the magnetic sheet.
    As a plus, when the job is finished, you remove this layer, bend it and the prints are released very...
  5. Replies
    12
    Views
    3,832

    [ HOW TO ] Hi Tommy, thank you for your reply! Yes, I did...

    Hi Tommy, thank you for your reply!

    Yes, I did so. Currently the Z-Gap is set to -2.418 and that may be OK but I am not absolutely sure it it is correct.
    What is your Z-Gap with the glass...
  6. Replies
    6
    Views
    2,404

    Hola Marmii, buen día! El diseño de razor81...

    Hola Marmii, buen día!

    El diseño de razor81 parece ser la solución que estás buscando y creo que puede servirte.

    Es muy difícil conseguir repuestos para esta impresora y menos aquí en...
  7. Replies
    12
    Views
    3,832

    [ HOW TO ] Calibrate a new PEI magnetic bed.

    Hi all!
    I was looking to improve the adhesion to the build plate of my Cube 3 and, after reading a lot about different options and seeing what is available here in my Country, I decide to buy a...
  8. Replies
    5
    Views
    2,508

    Hi Doug, I just use the Cube Print 4.03 that came...

    Hi Doug, I just use the Cube Print 4.03 that came with the machine. I have not had the opportunity to try another slicer yet.
  9. Replies
    5
    Views
    2,508

    Hi Tommy! I want to thank you very much for...

    Hi Tommy!
    I want to thank you very much for sharing this development and also encouraging other members to do it and take the advantage of using it.

    I was thinking in a way to stabilize the build...
  10. Thread: Universal Hub

    by Leonardo
    Replies
    82
    Views
    192,682

    I think that, in my case, the problem is that the...

    I think that, in my case, the problem is that the Teflon tube is quite soft and slippery.
    I made the grooves in my lathe so they were perfectly parallel and 0.45 mm deep but the tube slips out...
  11. Replies
    7
    Views
    3,199

    I liked the battery holder! I will 3d print it to...

    I liked the battery holder! I will 3d print it to see the stitching in hand.
    Thank you so much again!
  12. Replies
    7
    Views
    3,199

    Thank you very much TommyDee! I will redesign...

    Thank you very much TommyDee!

    I will redesign the box taking in account all your suggestions and will print it so see what happen. I think that it will works.

    Have a nice weekend!
  13. Replies
    7
    Views
    3,199

    I can understand what you are telling me...

    I can understand what you are telling me TonnyDee, but actually these are not separate walls that I want to afix together.
    These walls are created by the extrusor passing in parallel paths. I can...
  14. Thread: Universal Hub

    by Leonardo
    Replies
    82
    Views
    192,682

    The blue ring is just a slice of a 2x4 mm air...

    The blue ring is just a slice of a 2x4 mm air polyamide tube with an axial cut (not shown) to let it be inserted on the other tube.
    Unfortunately it slips out too. Although I liked very much the...
  15. Replies
    7
    Views
    3,199

    Problems with 3D printed box's walls.

    Hi all!

    I am looking for some advise from you, experienced Cube3 users, to solve a problem that I have with my first design to be printed with my new machine.

    I designed a little box in AutoCAD...
  16. Thread: Universal Hub

    by Leonardo
    Replies
    82
    Views
    192,682

    Report. Well, the original filament in the stock...

    Report.
    Well, the original filament in the stock cartridge definitely did not work at all. The new black filament that I bought was not so good, it cracks very easily so I went to buy the best...
  17. Thread: Universal Hub

    by Leonardo
    Replies
    82
    Views
    192,682

    Thank you so much to both of you for your quick...

    Thank you so much to both of you for your quick reply! And yes, I was talking about those "cooling tower"... added to the vocabulary of my poor English!

    Now I understood its function very well....
  18. Thread: Universal Hub

    by Leonardo
    Replies
    82
    Views
    192,682

    Hi TommyDee, I am new to the forum and also a...

    Hi TommyDee,
    I am new to the forum and also a totally newbie to 3D printing.
    First of all I want to thank you and all the other people who contribute for all these developments to solve the...
Results 1 to 18 of 18