Search:

Type: Posts; User: TommyDee

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    296
    Views
    49,118

    Sticky: Thanks for sharing that. I have all the parts. ...

    Thanks for sharing that. I have all the parts. Just need time with a soldering iron and some FW uploading.

    I almost pulled the trigger on the Rekindle version so making a donation to unlock the...
  2. Replies
    6
    Views
    69

    Will your IOS load the default 3D Systems app? ...

    Will your IOS load the default 3D Systems app? That's the best place to start.
    Remember that the Cube3 is a closed system to the 3DS app and the M$ app 3DBuilder.
    Mythandar created an app that...
  3. Replies
    64
    Views
    5,975

    Sticky: What's a Inf Rinse chip worth these days?

    What's a Inf Rinse chip worth these days?
  4. Replies
    6
    Views
    69

    ...and 3D Builder if you are on Windows 10

    ...and 3D Builder if you are on Windows 10
  5. Replies
    4
    Views
    107

    A thin Lithophane will print without fill if you...

    A thin Lithophane will print without fill if you limit the thickness.
    This allows the depth of the print to come through with light.
    It is the layer thickness that makes up most of the...
  6. Replies
    4
    Views
    104

    That can't be good... but it should only deal...

    That can't be good... but it should only deal with the wire management. But underneath that could be more issue.
    If this strains a wire, then yes, it could "glitch" into thinking it is a valid...
  7. Replies
    296
    Views
    49,118

    Sticky: Now I understand :) The temperature change app...

    Now I understand :)

    The temperature change app is by Mythandar. It is posted somewhere here on the forum.
    I haven't used it but I am not sure how the conversion app wouldn't work.
    Then again,...
  8. Replies
    296
    Views
    49,118

    Sticky: There are some options, such as the temperature...

    There are some options, such as the temperature changing app, that can change the .cube3 file temperature settings.
    This would allow you to use a PLA chip with ABS filament loaded.

    The premium...
  9. Replies
    4
    Views
    104

    Do you get an error message just before it stops?...

    Do you get an error message just before it stops?

    Tnn errors are associated with thermal issues at the nozzles.
    Chip disconnect errors give you 30 seconds to correct.
    A power supply disconnect...
  10. :o enjoy!

    :o enjoy!
  11. Okay, the default auto-gap is set in calibration....

    Okay, the default auto-gap is set in calibration. After it performs cal1 and set with a generous clearance, press the screen just to the right of the Cal2 label. This will initiate another...
  12. You want the auto-level to work. Without it, you...

    You want the auto-level to work. Without it, you have some unknown leveling state in the machine that you have to work with when manually leveling. Simple way to make auto-leveling work is to cover...
  13. Replies
    296
    Views
    49,118

    Sticky: I am vested in Print-R-Bot filament for general...

    I am vested in Print-R-Bot filament for general purpose. It is a little touchier about sticking to LokBuild. I back it with CubeGlue.
    Also liking the 3D Solutech for its vivid color. Most like...
  14. Replies
    296
    Views
    49,118

    Sticky: Right at this moment, you can probably beat $200...

    Right at this moment, you can probably beat $200 to your door on eBay. These deals cycle until the remaining inventory is exhausted.

    This printer is in a nutshell, the culmination of all the...
  15. Replies
    296
    Views
    49,118

    Sticky: http://www.print3dforum.com/showthread.php/1099-In...

    http://www.print3dforum.com/showthread.php/1099-Interesting-reading-(on-the-Cube3-hack)
  16. Replies
    296
    Views
    49,118

    Sticky: The "patch" doesn't deal with 0% cartridges. But...

    The "patch" doesn't deal with 0% cartridges. But there I a solution for that as well.
  17. Replies
    296
    Views
    49,118

    Sticky: vampi; can you clarify?

    vampi; can you clarify?
  18. Replies
    296
    Views
    49,118

    Sticky: If I understood, vampi copied the 2.0 fw onto a...

    If I understood, vampi copied the 2.0 fw onto a thumb drive renamed as 2.02. Then initiated the fw update.
  19. Replies
    1
    Views
    85

    [ HOW TO ] https://openbuilds.com/threads/cube-3-pro-hacks.84...

    https://openbuilds.com/threads/cube-3-pro-hacks.8420/
  20. Replies
    296
    Views
    49,118

    Sticky: The .ar file is the compiled firmware. This is...

    The .ar file is the compiled firmware. This is what is burned to the motherboard chip. In Cube3, they rename whatever the version name is to Magellan.ar. From there, there must be an OS process...
  21. Thread: HubCap V1

    by TommyDee
    Replies
    56
    Views
    1,698

    [ THING ] If it helps, Todd, the push nut has plenty of...

    If it helps, Todd, the push nut has plenty of iron to allow a magnet to help in the search.
  22. Thread: HubCap V1

    by TommyDee
    Replies
    56
    Views
    1,698

    [ THING ] Oh, you got me there... yes, push-nut. How'd you...

    Oh, you got me there... yes, push-nut. How'd you loose that?

    You might try ACE h/w. I suspect it is actually an SAE 1/8" diameter shaft version.
  23. Thread: HubCap V1

    by TommyDee
    Replies
    56
    Views
    1,698

    [ THING ] Which nut did you drop, Todd? I don't see a nut...

    Which nut did you drop, Todd? I don't see a nut in the build pix.

    https://cdn.thingiverse.com/assets/d9/3f/41/bf/99/parts.jpg

    - - - - - - - - - -


    I was just only curious to see if I could...
  24. Thread: HubCap V1

    by TommyDee
    Replies
    56
    Views
    1,698

    [ THING ] zugok; what pitch did you end up with on the cap...

    zugok; what pitch did you end up with on the cap thread?
  25. Replies
    257
    Views
    32,334

    [ HOW TO ] Two alternate solutions to the 3DS support...

    Two alternate solutions to the 3DS support function:
    1) Model the supports in your base geometry model.
    2) Use MeshMixer


    Making your own support requires about .008"-.010" z-gap if you want to...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4