Search:

Type: Posts; User: TommyDee

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    27
    Views
    164,918

    Sticky: I can still do this nicko.

    I can still do this nicko.
  2. Replies
    1
    Views
    67

    Too hot. PLA likes around 80 degrees in the room...

    Too hot. PLA likes around 80 degrees in the room and no heating of the bed. Make sure the nozzle isn't radiating excess heat at the print.
  3. Replies
    326
    Views
    542,681

    Sticky: You might consider a local STEM program in a...

    You might consider a local STEM program in a local school. Although this is a great offer, and I would take you up on it if it came to $50 or less, a local program for kids and young adults may...
  4. You hear the ticks. It is a process. But you...

    You hear the ticks. It is a process. But you can test it with a border print to see if the filament is equally wide all around as a test.

    I've lain a white sheet of paper on the surface to fool...
  5. Have a look here -...

    Have a look here - http://www.print3dforum.com/showthread.php/1165-Z-ticks?highlight=z-ticks

    I don't ever auto-level.
  6. Replies
    3
    Views
    368

    Some people here have parted out machines and...

    Some people here have parted out machines and offered parts. Sometimes they show up on Ebay. It is hard to find parts. Feel free to post for parts in CubePro for-sale/trade section. Here is a...
  7. Replies
    3
    Views
    368

    This is likely a sensor failure on the motor...

    This is likely a sensor failure on the motor controller board. The system monitors the black and white 'flags' on the filament drive wheels. If that is not getting processed or something is wrong...
  8. Replies
    16
    Views
    16,036

    It is probably a MOV on the heater control...

    It is probably a MOV on the heater control module. Seen that picture before. But the factory 2.02 upgrade was fine, I still run it. I honestly think that settings go out of bounds for the heater...
  9. Replies
    34
    Views
    30,323

    Sticky: You can write a custom g-code (*.cubepro) file...

    You can write a custom g-code (*.cubepro) file that only initiates the heater.
  10. Thread: Wood Filament

    by TommyDee
    Replies
    3
    Views
    570

    Connect with Tamir1an

    Connect with Tamir1an
  11. Aha, now I understand what you are after. I have...

    Aha, now I understand what you are after. I have not captured that print file. Hopefully someone else here has this in their archives and is willing to post it.

    If you want to, you could try to...
  12. All you can do is request the files. The user...

    All you can do is request the files. The user doesn't participate here anymore.

    You are also welcome to check some of my alternatives on thingiverse - https://www.thingiverse.com/qube3bot/designs...
  13. Replies
    8
    Views
    5,615

    Something to do with entering a code?

    Something to do with entering a code?
  14. Replies
    26
    Views
    7,339

    More gap. To little gap presents to the machine...

    More gap. To little gap presents to the machine like a clog.
  15. Replies
    26
    Views
    7,339

    Not from the pictures. You could try unplugging...

    Not from the pictures. You could try unplugging them and see if it boots after that.
  16. Replies
    26
    Views
    7,339

    Looking good so far. I use CubeGlue on my...

    Looking good so far.

    I use CubeGlue on my LokBuild for great service. However, LokBuild does work well without glue with several materials.

    Glue on LokBuild can be recharged by simply misting...
  17. Replies
    9
    Views
    1,579

    The only posts we've seen about failed heaters...

    The only posts we've seen about failed heaters was after the hack so I bet it is the culprit. Not sure how it would do that though. Somewhere in the firmware is where the chamber temperature is...
  18. Replies
    9
    Views
    1,579

    The fan on the heater is on all the time but the...

    The fan on the heater is on all the time but the heater has a thermal fuse internally to stop heating. Technically, it should be hardwired to the AC input.

    I am not sure anyone has investigated...
  19. Replies
    9
    Views
    1,579

    There should be a version 2.02. Yes, .ar is the...

    There should be a version 2.02. Yes, .ar is the right extension and cubepro is the appropriate prefix.
  20. Replies
    9
    Views
    1,579

    We have the Cubify repository stored among us. ...

    We have the Cubify repository stored among us.

    http://www.print3dforum.com/showthread.php/3024-3DS-Cube-File-Links
  21. Print a 6" x 6" border. Two of the magnets under...

    Print a 6" x 6" border. Two of the magnets under the bed are adjustable.
  22. Replies
    26
    Views
    7,339

    Your saying leave the metal piece and forget the...

    Your saying leave the metal piece and forget the plastic 'guide" Doug?

    - - - - - - - - - -


    Let's do this one step at a time - first things first, let's get the hardware on correctly;

    1) we...
  23. Replies
    26
    Views
    7,339

    The metal plate behind plastic tube guide was on...

    The metal plate behind plastic tube guide was on backwards. The black track needs to mount to the front of the metal plate and things will reach.

    This is the same orientation;
    4424
  24. Replies
    26
    Views
    7,339

    Do any of these help? Not familiar with a glass...

    Do any of these help? Not familiar with a glass part.

    4420442144224423
  25. Replies
    367
    Views
    396,576

    No spare spares, no. That stuff looks fantastic.

    No spare spares, no. That stuff looks fantastic.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4