Search:

Type: Posts; User: bolsoncerrado

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    1
    Views
    45

    Pretty much doable, as long as you know how to...

    Pretty much doable, as long as you know how to edit the firmware sizes and then apply the hardware upgrades.
  2. Did you check if archive.org did this already?

    Did you check if archive.org did this already?
  3. Replies
    2
    Views
    74

    Are you on the same WIFI network?

    Are you on the same WIFI network?
  4. Replies
    129
    Views
    34,713

    Sticky: Perhaps a README would help too :P

    Perhaps a README would help too :P
  5. Why do u care to reply to this spam @Tommy?

    Why do u care to reply to this spam @Tommy?
  6. Replies
    9
    Views
    603

    I'm pretty sure it's possible, as long as you...

    I'm pretty sure it's possible, as long as you have the firmware to go with it.
  7. See if this helps:...

    See if this helps: https://www.dropbox.com/s/7d1bhebmbmooksh/SD%20RAPIDE%20LITE%20200.zip?dl=0
  8. Replies
    4
    Views
    560

    Since there is no heatbed on the Cube3 i wouldnt...

    Since there is no heatbed on the Cube3 i wouldnt be that much concerned.
  9. Replies
    3
    Views
    440

    ?? whats going on here?

    ?? whats going on here?
  10. What temp requirements have this nylon? I hear...

    What temp requirements have this nylon? I hear its the worst filament to fight against humidity so old filament could be a serious issue...
  11. This pic here gave me some dirty ideas HaHaHa :D

    3341


    Perhaps an hybrid we could run the nema outside the cube?
  12. Replies
    206
    Views
    47,965

    Sticky: You mean stock cube3 carts "pre-modified" before...

    You mean stock cube3 carts "pre-modified" before installation?
  13. Replies
    7
    Views
    701

    [ THING ] WOw you already built one? :) YOur review in...

    WOw you already built one? :)

    YOur review in 3, 2, 1...
  14. Did you check the start Gcode as well?

    Did you check the start Gcode as well?
  15. Creality Ender still is a hot cake if you look...

    Creality Ender still is a hot cake if you look for a "cheap chinese printer" but you end up having to tweak it sooner or later...

    It all depends on your budget and how much/how often do you want...
  16. Replies
    4
    Views
    514

    Id do a fresh wiring with brand new endstop just...

    Id do a fresh wiring with brand new endstop just to be completely sure its not a faulty boad and triple check the connectors to the board too...replacing the board will be exhausting.
  17. Replies
    4
    Views
    514

    When you replaced the switches did you replace...

    When you replaced the switches did you replace the wiring too?
  18. Replies
    4
    Views
    1,217

    WIth or without glue?

    WIth or without glue?
  19. Replies
    18
    Views
    6,895

    Fckin' spammer.... :/

    Fckin' spammer.... :/
  20. Replies
    2
    Views
    450

    Did you try their official online store?

    Did you try their official online store?
  21. Are we supposed to ask about Creawesome so we're...

    Are we supposed to ask about Creawesome so we're spammed with it now?

    I'm about to hit the BAN button...
  22. If it was in an Ender, you're in the wrong...

    If it was in an Ender, you're in the wrong subforum then :)
  23. Cube Pro Total Conversion: A step-by-step guide on how to "Open source" it...

    Interesting / Inspiring reading!

    https://dyzedesign.com/2018/09/cube-pro-total-conversion-step-by-step-guide/
  24. Replies
    29
    Views
    3,709

    Sticky: You may want to start a new thread with the tool...

    You may want to start a new thread with the tool and instructions on the first post? :D
  25. THe only one i know of that permanently changes...

    THe only one i know of that permanently changes slightly is the wooden infused filament because it actually "overburns" the wood particles inside...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4