Search:

Type: Posts; User: SAO

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    108
    Views
    85,274

    I am not at this step, but I will do it with that...

    I am not at this step, but I will do it with that :

    http://marlinkimbra.it/?lingua=en
  2. I just sent a message to Ethan to have...

    I just sent a message to Ethan to have additionnal informations.

    I will tell you when I have an answer
  3. did somebody ordered the XL option or the dual...

    did somebody ordered the XL option or the dual extruder option? and did you received something ?

    I don't succeed to have clear informations
  4. Replies
    108
    Views
    85,274

    Thanks Bob for the advice. there is a bar on...

    Thanks Bob for the advice.

    there is a bar on the top of the arms to make all compact, sorry i don't installed it for the moment.

    I have wait to install that because I was waiting the XL option,...
  5. Replies
    108
    Views
    85,274

    It can't move because it is inserted on the frame...

    It can't move because it is inserted on the frame and locked with "keys" behind.
    The weight is evenly distributed along the axis of the frame

    I have tested the pieces, and normally, it is enough,...
  6. Replies
    108
    Views
    85,274

    1094 I have installed the bracket for the...

    1094

    I have installed the bracket for the motors, for the spool.
    Can put 6 different spools and 5-6 extruders motors
    The motors will be vertically in order to have the filament horizontaly...
  7. Thread: X Wing Slider

    by SAO
    Replies
    82
    Views
    56,456

    Waou, it is impressive !!!! You have done a...

    Waou, it is impressive !!!!

    You have done a lot of works.!!

    How about the printing ? Does It print well ?
  8. Replies
    6
    Views
    10,773

    to have the history : click on "Get More" and...

    to have the history :

    click on "Get More"
    and type "history"
    you will have this :
    1075

    Click on "install"
    and wait the end of the installation
    Then close the popup window install.
  9. Replies
    6
    Views
    10,773

    To have the temperatures on the nav bar : 1073 ...

    To have the temperatures on the nav bar :
    1073


    open settings menu
    1074
    Click on "get more"
    and search "navbar"

    The plugin appear with an install button on the right.
  10. Replies
    6
    Views
    10,773

    In order to have the update : open the LX...

    In order to have the update :

    open the LX Terminal and type (depending of the version you have) :
    How can I update the OctoPrint installation on my OctoPi image?

    You'll first need to ssh...
  11. Replies
    6
    Views
    10,773

    Thanks for the info Bolson I will try to make...

    Thanks for the info Bolson
    I will try to make the update tomorow
  12. Replies
    19
    Views
    12,478

    Good news. Happy it works again :)

    Good news.

    Happy it works again :)
  13. Replies
    19
    Views
    12,478

    I am just a beginner in soldering and it was...

    I am just a beginner in soldering and it was easy.

    I cut the wires just after the old thermistor and I have soldered the new.
    I have put ptfe tub 0.3 mm ID 0.6 OD to insulate the thermistor...
  14. Replies
    19
    Views
    12,478

    The ptfe tub in the thermal tube is in silicone,...

    The ptfe tub in the thermal tube is in silicone, which can be heated to 250° without melted.
    Normally it is a slippery material, but I have forced to remove mine because there was an important jam....
  15. Replies
    19
    Views
    12,478

    For the thermal tube : the side near the block...

    For the thermal tube :

    the side near the block heater :
    1065

    You can see the ptfe tube.

    You insert a small allen key or anything small on the opposite side, and the pfte will go out
    you...
  16. Replies
    19
    Views
    12,478

    I don't explain the bed temp issue (perhaps the...

    I don't explain the bed temp issue (perhaps the problem with your extruder thermistor and the strange temp it show don't allow you to change any temp)

    Thermistor are very fragile, perhaps yours is...
  17. Replies
    19
    Views
    12,478

    Hi, I have questions about the thermistor,...

    Hi,

    I have questions about the thermistor, normally a thermistor look like that :
    1061
    You said that the cable came out, the wire only or with the head ?
    If it was only the wire, you broke it...
  18. Replies
    108
    Views
    85,274

    you have to install the heatsink, the thermistor,...

    you have to install the heatsink, the thermistor, the extruders, the new bracket nozzle, to modify the firmware...
  19. Replies
    108
    Views
    85,274

    Nice news. I look forward to see it installed :)...

    Nice news.
    I look forward to see it installed :)

    I miss only the MK8 gears drive.
    I have installed the bracket for the 5-6 extruders
    I have printed the bracket for the 5-6 spools
    I will modify...
  20. Thread: My Rapide Lite 312

    by SAO
    Replies
    16
    Views
    19,435

    Very nice job !

    Very nice job !
  21. Replies
    81
    Views
    46,932

    Sorry for this problem

    Sorry for this problem
  22. Replies
    108
    Views
    85,274

    I print XT copolyester (which is food contact,...

    I print XT copolyester (which is food contact, without bisphenol A...), at small speed 20-40 mm/s at 243-247° but I can't increase a lot the speed because I would have to increase the temp.
    And I...
  23. Replies
    18
    Views
    12,486

    nice bought :)

    nice bought :)
  24. Replies
    108
    Views
    85,274

    With the relay system we could have 6 extruders...

    With the relay system we could have 6 extruders max and 6 nozzles max but we loose a lot of printing surface.
    It is for that it will be better and cheaper to have 3 nozzles instead of 6.

    Thanks...
  25. Replies
    108
    Views
    85,274

    Hi Bob, I have choosen the E3D V6 because I...

    Hi Bob,

    I have choosen the E3D V6 because I wanted to have high temp, and it is easier for the bracket to have the same dimensions on all hot ends.
    But It was not a good choice it seems.
    I...
Results 1 to 25 of 207
Page 1 of 9 1 2 3 4