Search:

Type: Posts; User: TommyDee

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    36

    I replied with an epic 2 part response, Tarak. I...

    I replied with an epic 2 part response, Tarak. I look forward to understanding how we can downgrade these monsters to install the modified F/W. Be sure not to overlook method 5 at the end of the...
  2. Replies
    0
    Views
    5

    Happy Easter everyone!

    3232
  3. Replies
    5
    Views
    25

    :) never much liked dealing with recipes. ...

    :) never much liked dealing with recipes. Overall, not bad on the second go. Good luck, Trickle.
  4. Replies
    5
    Views
    25

    Overall that looks a lot more consistent. There...

    Overall that looks a lot more consistent. There is nowhere for the slicer to hide the seam. How bad is the seam if you don't randomize?
  5. Replies
    140
    Views
    21,518

    Sticky: :p The thing they thread on the Teflon tubing is...

    :p The thing they thread on the Teflon tubing is a barrel nut. I don't use them for any configuration. Those are the bane of Cube3!

    - - - - - - - - - -

    I'll send you the one I took off that...
  6. Replies
    5
    Views
    25

    I've heard that the random seams cause this type...

    I've heard that the random seams cause this type of artifact using Cura. I don't know how to gauge Cr-10 for overall print quality. I do now that the more consistent your motion profile is, the...
  7. Replies
    5
    Views
    36

    My experience is Cube3 and if you put the...

    My experience is Cube3 and if you put the firmware of choice on the USB stick, you can use the menu to update F/W. It should ignore the current version and load whatever is on the stick, but only...
  8. Replies
    3
    Views
    322

    Welcome to the forum, smithclarkson01!

    Welcome to the forum, smithclarkson01!
  9. Replies
    140
    Views
    21,518

    Sticky: Oh, that's the push nut I was referring to...

    Oh, that's the push nut I was referring to earlier :p

    Do I need to send that too?
  10. Replies
    5
    Views
    36

    If you really want to use the latest firmware,...

    If you really want to use the latest firmware, make or get a chip resetter. I'll reset your chips for free until we can get you up an running with one. Lots of ways to get there. Talk to me. Got...
  11. Replies
    5
    Views
    31

    No trouble at all, R4D. I like seeing these...

    No trouble at all, R4D. I like seeing these little printers making great parts!
    Also kudos to the person that sold you a properly upgraded system.
    Happy Printing!

    3226
  12. Replies
    5
    Views
    31

    Thanks for the information on the hardware mod. ...

    Thanks for the information on the hardware mod. I will post them as pictures soon. I had not seen this mod before. Someone did a nice work for making the printer functional for you.

    The test...
  13. Replies
    5
    Views
    31

    Welcome to the forum, R4D. Your issue is not...

    Welcome to the forum, R4D.

    Your issue is not too difficult. There is a requirement in the Cube Print that a certain firmware level on the Cube3 printer is installed. The printer reports to the...
  14. Welcome to the forum, Pr1nt! Do other devices...

    Welcome to the forum, Pr1nt!

    Do other devices take their sweet time getting connected on your network?
    As stated before, my router was limited in allowable connections. Not being savvy on...
  15. Replies
    140
    Views
    21,518

    Sticky: My pleasure, Shawn. The envelope should follow...

    My pleasure, Shawn. The envelope should follow tomorrow.
  16. Kester Flux Pen! No worries, I'm of a similar...

    Kester Flux Pen! No worries, I'm of a similar skill level with very different intent. You might find these dragons are a lot tamer than others lurking about. Anyone ever get a real conversation...
  17. That's a great write-up! Indeed, the connections...

    That's a great write-up! Indeed, the connections are the same where only D10 (master) to Reset (slave) as the variation on the 6 pins.

    The Melzi pinout or the Mega pinout? I was not even aware...
  18. Aha... No bootloader on the original? That's...

    Aha... No bootloader on the original? That's strange.

    In the ReCube thread under Cube3 I went through the bootloader process using a Nano master to Nano slave. Worked wonders.
    This loads the...
  19. Replies
    25
    Views
    1,634

    [ HOW TO ] Once you find haxtom, I think you're there! -...

    Once you find haxtom, I think you're there!

    - - - - - - - - - -

    This rarely happens... Today I received a second NANO from a previous order for only one Nano. Its got all the pins soldered in...
  20. Just learned about this trick recently and have...

    Just learned about this trick recently and have not done anything with it, but I do know how to replace the standard bootloader.
    Doesn't recover any additional space, however. You can start looking...
  21. Any other useless bit of code you can remove? ...

    Any other useless bit of code you can remove? Remove an unnecessary library? Any non-CR10 functionality that can be remarked?
  22. Sticky: We are making progress! Please post a picture of...

    We are making progress! Please post a picture of what you -are- seeing and we can go from there.
  23. Thread: Universal Hub

    by TommyDee
    Replies
    50
    Views
    6,586

    Time for this thread to make it back to the top....

    Time for this thread to make it back to the top.

    Today I went in and made a small improvement to the universal hub.

    These cartridges were redesigned to simplify universal access with many...
  24. Replies
    0
    Views
    38

    The ReCube Wand Help Thread.

    Welcome to the ReCube Wand help thread.
    Restoring the code of the light version of ReCube on the Arduino Nano device
    ~or~
    Upgrading to Tomuro's ReCube Pro code, this is the place for discussions....
  25. Thread: new to forum

    by TommyDee
    Replies
    1
    Views
    50

    Welcome to the forum dgils! The Kossel delta...

    Welcome to the forum dgils!

    The Kossel delta printers are very interesting. I do not know if there have been discussions here or not.

    However, please feel free to create a discussion and let...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4