Search:

Type: Posts; User: TommyDee

Search: Search took 0.00 seconds.

  1. Replies
    48
    Views
    4,051

    You tell me. Make a huge gap without pressing...

    You tell me. Make a huge gap without pressing CAL2 and see where it gaps to. This is what sets the initial gap in Auto-gap.
  2. Replies
    48
    Views
    4,051

    Go through the maintenance routine and set the...

    Go through the maintenance routine and set the default gap there (CAL1). I give it an extra 3mm just to make sure it never crashes... or 5mm gap for my glass plate conversion (magnets below the...
  3. Replies
    48
    Views
    4,051

    There is a nasty layer of serious double stick...

    There is a nasty layer of serious double stick glue under there!
    Even with Xylene, it took hours to clean up... and Xylene is a serious neurotoxin!
    Gloves, stiff breeze level ventilation, and a...
  4. Replies
    48
    Views
    4,051

    Confirmed that the Cube 3 doesn't care about the...

    Confirmed that the Cube 3 doesn't care about the writing or the surface of the orange LokBuild with black text. It levels, calibrates, and gaps perfectly.

    there really is no way to level manually...
  5. Replies
    48
    Views
    4,051

    It didn't work. The disk requires a tool I don't...

    It didn't work. The disk requires a tool I don't have and the abrasive is impregnated in rubber.

    Interesting about the magnets. I wonder if the heat adds its own stiction to the nylon magnet...
  6. Replies
    48
    Views
    4,051

    Tried a glass etching cream on the b-glass. It...

    Tried a glass etching cream on the b-glass. It just laughed at it. Not even a minor scuff.

    In case you're wondering, I want the borosilicate glass to be recognized for leveling.
    Ordered a 300...
  7. Replies
    48
    Views
    4,051

    Much better. Building on the borosilicate...

    Much better.

    Building on the borosilicate glass with cube glue again. I really like the way it takes PLA.
    I can see through the plate to see where it remained stuck.
    The part pops off easily...
  8. Replies
    48
    Views
    4,051

    Good luck Gary. The Lokbuild should solve your...

    Good luck Gary. The Lokbuild should solve your issue.

    See if they have tape from IGP. I highly recommend it.
    I looked locally and only found the .88" wide tape after looking at 6 stores.

    - -...
  9. Replies
    48
    Views
    4,051

    Complete the calibration process :) A lot of...

    Complete the calibration process :)

    A lot of systems went out that crashes the build plates.
    Knowing how to successfully complete this function is what resets the home location.
  10. Replies
    48
    Views
    4,051

    I suspect the first layer is velocity 50% and...

    I suspect the first layer is velocity 50% and extrude rate normal... or something like that. Also, the head temp is really amp'd for the first layer.
  11. Replies
    48
    Views
    4,051

    Anytime! Use it wisely (this is how you can use...

    Anytime! Use it wisely (this is how you can use a tall heating plate!!!)
  12. Replies
    48
    Views
    4,051

    I'm talking about the maintenance screen... This...

    I'm talking about the maintenance screen...
    This is where you set the default from where it begins auto-gap and leveling.
    My normal position for my gap is -3.00. I do not gap to this auto-cal.

    ...
  13. Replies
    48
    Views
    4,051

    There is a maintenance routine that sets the...

    There is a maintenance routine that sets the default gap.
    I overset this gap by a lot.
    This ensures the plate doesn't crash into the nozzle.
    Look for the unidentified button for the lower...
  14. Replies
    48
    Views
    4,051

    Funny thing is, the IPG tape lets go on the...

    Funny thing is, the IPG tape lets go on the tape's adhesive side before it let's go of the part :)

    1892
  15. Replies
    48
    Views
    4,051

    Oh, contraire, Bo. Two observations: 1) "just...

    Oh, contraire, Bo.

    Two observations:
    1) "just clean it" implies simplicity. There is nothing simple about removing the adhesive! It took major chemical aggression to remove the glue. As in...
  16. Replies
    48
    Views
    4,051

    Alumina surface :p Hardly. I'm finally having...

    Alumina surface :p Hardly.

    I'm finally having some luck with this. But alumina is not the material to stick too unless you have a heating situation figured out.

    I put a 6" alumina square on...
Results 1 to 16 of 16