Search:

Type: Posts; User: dougk12

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    124

    PM sent :)

    PM sent :)
  2. Replies
    5
    Views
    244

    Oh yes! You are in it now my friend :) PM me and...

    Oh yes! You are in it now my friend :) PM me and I'll get an imperfect bed in the mail to you - the bed wobbles in place so you'll need to remove all three magnets, clean the back and then reinstall...
  3. Replies
    3
    Views
    124

    Ugggh, I do but I'm in the US. I think the...

    Ugggh, I do but I'm in the US. I think the shipping costs would crush you :(.
  4. Replies
    3
    Views
    84

    OK, this sounds to me like you upgraded the...

    OK, this sounds to me like you upgraded the printjet but didn't activate the advanced printjet feature in the setup. It isn't that it doesn't see the cartridge, it just won't accept anything other...
  5. Replies
    5
    Views
    244

    Hi and welcome to the forum. I wish I had noticed...

    Hi and welcome to the forum. I wish I had noticed this post sooner because I have a ton of xp with these printers and extra parts. I also love supporting STEM programs.

    By now, you’ve probably...
  6. Replies
    3
    Views
    84

    No longer recognized? If you push the cartridge...

    No longer recognized? If you push the cartridge into place and then go to cartridge status in the menu, do you see it installed (IE, don't bother with the change cartridge function)? If not, are the...
  7. Thread: Wood Filament

    by dougk12
    Replies
    3
    Views
    556

    I wouldn't recommend it in the Cube3. The pro did...

    I wouldn't recommend it in the Cube3. The pro did it through the advanced nozzle, which was a .5mm print tip. It might be very difficult to remove a wood grain clog in the print tip.
  8. Here you go! It was ~12 posts below this one :) ...

    Here you go! It was ~12 posts below this one :)

    http://www.print3dforum.com/showthread.php/5044-Autoloading-print-files-for-Cube3

    Please read the instructions and watch the YouTube video....
  9. Replies
    1
    Views
    526

    It looks like your z gap needs to be loosened up...

    It looks like your z gap needs to be loosened up a little. I recommend the calibration print files, especially when changing to print in Nylon or Wood. Some filament types need a little more of a...
  10. Does anyone have the ManualPatch.zip re: Invalid Serial Number error on Cube3?

    I am at the tail end of repairing a few Cube3s and hoping to save a spare board with the Invalid Serial Number issue.

    My board shows as FW v1.07. I have a good V1.14B board right next to it but...
  11. I'm excited to see this project completed Jammin....

    I'm excited to see this project completed Jammin. I know you've put a ton of work into it and with zero prior experience with the CubePro that is no small task. Please keep us informed once you're...
  12. Replies
    5
    Views
    1,360

    Awesome! Always happy to hear about another Cube3...

    Awesome! Always happy to hear about another Cube3 avoiding the landfill :)
  13. Replies
    5
    Views
    1,360

    Hey Wiz, I have a spare one of these that you are...

    Hey Wiz, I have a spare one of these that you are welcome to. It appears that you've removed the linear rail seat, which I believe is a no no. I can see one of the balls missing in your pic.
    ...
  14. Sometimes when my auto-calibrate is off and the...

    Sometimes when my auto-calibrate is off and the printer doesn't detect it, I adjust pads 2 and 3 (pad 1 - upper left hand corner shouldn't be adjusted) one way a 1/2 turn and then re-run. Another...
  15. Replies
    9
    Views
    1,547

    Yes, look at the next post down :) I know he's...

    Yes, look at the next post down :) I know he's already moved the printjet assembly but I bet he still has this.
  16. Replies
    26
    Views
    7,289

    No, not at all. I've always wrestled with getting...

    No, not at all. I've always wrestled with getting the filament to catch when reloading. Not sure if this is a common issue or not but it was very frustrating for me. This solves that and the only...
  17. Replies
    26
    Views
    7,289

    That guide is held in place with nuts & bolts. It...

    That guide is held in place with nuts & bolts. It appears you are missing a couple at the top of it.

    I would recommend losing that altogether. It's purely aesthetic and serves no functional...
  18. Replies
    26
    Views
    7,289

    The small triangle that goes in the bottom right...

    The small triangle that goes in the bottom right hand corner of that assembly uses a longer bolt and mounts threw the bottom right hand hole. It isn't required - I believe it's purpose is to prevent...
  19. Replies
    4
    Views
    1,186

    Hi, I'm interested in the printjets and system...

    Hi, I'm interested in the printjets and system board (if you have the activation PIN or S/N). Please PM me.
  20. Replies
    3
    Views
    1,183

    Ah, what a shame :(. Send me a PM, I can make...

    Ah, what a shame :(. Send me a PM, I can make good use of the chips.
  21. Replies
    3
    Views
    1,183

    Sorry to hear that but I am interested and...

    Sorry to hear that but I am interested and sending you a PM.
  22. Nah dawg :) the only thing that printer cares...

    Nah dawg :) the only thing that printer cares about is the chip on that cartridge. If the material code filament type on the chip matches the material code filament type in the print file, it will...
  23. I'd like to get a hold of that modified version...

    I'd like to get a hold of that modified version of Eko firmware. Did you find it on this forum? I tried using the Cube Toolbox on a number of Eko firmware versions but no luck.
  24. Oh, you were able to use the toolbox to modify...

    Oh, you were able to use the toolbox to modify the EKO firmware so the cart never goes down? I wasn't aware that was an option! It absolutely works for the Cube 3 but I was under the impression that...
  25. Cool! I would advise that OEM ABS = good but...

    Cool!

    I would advise that OEM ABS = good but OEM PLA = bad. PLA is made out of corn and is compostable, even if it's been sealed in mylar for the past 5+ years it's very brittle. And there is no...
Results 1 to 25 of 102
Page 1 of 5 1 2 3 4