Search:

Type: Posts; User: TommyDee

Search: Search took 0.02 seconds.

  1. I'm in the same boat RicciEU. I'd do Simplify3D...

    I'm in the same boat RicciEU. I'd do Simplify3D in a heartbeat if I had the time.
  2. RicciEU; this is not the only bug in the slicer. ...

    RicciEU; this is not the only bug in the slicer. For some reason, every 8mm or so it wants to make a 'stiffening mesh' that always shows up on the outside walls. This very same operation will...
  3. The PETG I am using is NovaMaker. It likes 250C...

    The PETG I am using is NovaMaker. It likes 250C on Cube3. Will work at 260 ABS settings in a pinch but not perfect on sloped surfaces.
  4. Yea, fresh filament. Anytime you straighten the...

    Yea, fresh filament. Anytime you straighten the filament from the spool it will crack and break from the tension. It is simply outdated filament.
  5. There is one of those warmup 'prints' here in the...

    There is one of those warmup 'prints' here in the CubePro channel somewhere.
  6. I stocked up and making it last by diluting it a...

    I stocked up and making it last by diluting it a lot. I have no idea what the formula is. I just know that with LokBuild, it is the perfect adhesion medium.
  7. Skipping of the stepper means not flowing. I...

    Skipping of the stepper means not flowing. I have a feeling that different filament materials require significantly different profiles. When you compare the PLA/ABS profiles of Cube3 and the PETG...
  8. The heater is not keeping up with the flow rate. ...

    The heater is not keeping up with the flow rate. It could well be unsolvable depending on the melt profile of the filament. What is PETE anyway? I've gotten this with excess heat as well. I hate...
  9. Oh, now that's data! The heaters can't keep up. ...

    Oh, now that's data! The heaters can't keep up. That should be going right back to the controller. Can you get a voltmeter across extruder heater leads?
  10. I've had problems like this with Cube3. It was...

    I've had problems like this with Cube3. It was very specific to a lot of retractions. The nozzle wasn't keeping up and the walls of the PTFE tube would have cooler PLA forcing the melt to go...
  11. Does it sputter when it purges the PETG? I...

    Does it sputter when it purges the PETG?

    I don't know what hardware level code could be corrupt to cause this. I have used only admittedly old 3DS ABS to not have these kinds of issues. The PETG...
  12. This looks like under-extrusion. If the new and...

    This looks like under-extrusion. If the new and old nozzles behave the same, the hardware is functional. This is all about making recipes work. Are you running the PETG as the ABS slicer in...
  13. Short answer RicciEU - yes. Cube3 has shown me...

    Short answer RicciEU - yes. Cube3 has shown me that the ABS profile for Cubify material is 10*C higher than most conventional ABS formulations.

    I did run some white NovaMaker PETG using the ABS...
  14. Interesting to note the adjustable gap. That is...

    Interesting to note the adjustable gap. That is a new twist. Glad to see you got it working again. Acetone would have made a mess for sure.
  15. You are bold RicciEU. I run only 3DS ABS in my...

    You are bold RicciEU. I run only 3DS ABS in my CubePro Duo. I really don't want to learn how to unclog the nozzles. Is it possible your filament of choice requires a little extra temperature? I...
  16. I got something similar when ABS was running hot...

    I got something similar when ABS was running hot by about 10C.
Results 1 to 16 of 16