Search:

Type: Posts; User: bolsoncerrado

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds; generated 21 minute(s) ago.

  1. Replies
    2
    Views
    95

    Is your CR supplied with an ABL? Sort of BL-Touch?

    Is your CR supplied with an ABL? Sort of BL-Touch?
  2. Replies
    1
    Views
    150

    You may need to edit Marlin to reflect the...

    You may need to edit Marlin to reflect the thermistor change to a different type (ask the vendor?) or order from a differet supplier. Definetly not the same that ships with CR.
  3. Replies
    1
    Views
    102

    Any current chinese printer (Ender, Anet, etc.)...

    Any current chinese printer (Ender, Anet, etc.) should be cheap enough, but be prepared to tinker with...
  4. Replies
    1
    Views
    156

    Awesome job man, keep it going! ;)

    Awesome job man, keep it going! ;)
  5. Replies
    230
    Views
    53,020

    Sticky: !?!? Everything (or almost!) in this printer...

    !?!?

    Everything (or almost!) in this printer is salvageable specially the extruder part hehe
  6. Replies
    230
    Views
    53,020

    Sticky: Have you tried a torch nearby? Either pla or abs...

    Have you tried a torch nearby? Either pla or abs should fuse easily...
  7. Replies
    1
    Views
    138

    Pretty much doable, as long as you know how to...

    Pretty much doable, as long as you know how to edit the firmware sizes and then apply the hardware upgrades.
  8. Did you check if archive.org did this already?

    Did you check if archive.org did this already?
  9. Replies
    2
    Views
    164

    Are you on the same WIFI network?

    Are you on the same WIFI network?
  10. Replies
    140
    Views
    36,354

    Sticky: Perhaps a README would help too :P

    Perhaps a README would help too :P
  11. Why do u care to reply to this spam @Tommy?

    Why do u care to reply to this spam @Tommy?
  12. Replies
    9
    Views
    732

    I'm pretty sure it's possible, as long as you...

    I'm pretty sure it's possible, as long as you have the firmware to go with it.
  13. See if this helps:...

    See if this helps: https://www.dropbox.com/s/7d1bhebmbmooksh/SD%20RAPIDE%20LITE%20200.zip?dl=0
  14. Replies
    4
    Views
    638

    Since there is no heatbed on the Cube3 i wouldnt...

    Since there is no heatbed on the Cube3 i wouldnt be that much concerned.
  15. Replies
    3
    Views
    513

    ?? whats going on here?

    ?? whats going on here?
  16. What temp requirements have this nylon? I hear...

    What temp requirements have this nylon? I hear its the worst filament to fight against humidity so old filament could be a serious issue...
  17. This pic here gave me some dirty ideas HaHaHa :D

    3341


    Perhaps an hybrid we could run the nema outside the cube?
  18. Replies
    230
    Views
    53,020

    Sticky: You mean stock cube3 carts "pre-modified" before...

    You mean stock cube3 carts "pre-modified" before installation?
  19. Replies
    7
    Views
    796

    [ THING ] WOw you already built one? :) YOur review in...

    WOw you already built one? :)

    YOur review in 3, 2, 1...
  20. Did you check the start Gcode as well?

    Did you check the start Gcode as well?
  21. Creality Ender still is a hot cake if you look...

    Creality Ender still is a hot cake if you look for a "cheap chinese printer" but you end up having to tweak it sooner or later...

    It all depends on your budget and how much/how often do you want...
  22. Replies
    4
    Views
    570

    Id do a fresh wiring with brand new endstop just...

    Id do a fresh wiring with brand new endstop just to be completely sure its not a faulty boad and triple check the connectors to the board too...replacing the board will be exhausting.
  23. Replies
    4
    Views
    570

    When you replaced the switches did you replace...

    When you replaced the switches did you replace the wiring too?
  24. Replies
    4
    Views
    1,294

    WIth or without glue?

    WIth or without glue?
  25. Replies
    18
    Views
    7,088

    Fckin' spammer.... :/

    Fckin' spammer.... :/
Results 1 to 25 of 499
Page 1 of 20 1 2 3 4