Search:

Type: Posts; User: AngryPanda

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. @Jao, I ran into something similar when I was...

    @Jao,
    I ran into something similar when I was trying to setup my endstop. I accidentally bumped my Z- Stepper cable knocking it loose. When I realized what I did, I plugged it back in....
  2. Replies
    85
    Views
    67,749

    @all-nanodlp'ers here lol. So I have all my...

    @all-nanodlp'ers here lol.

    So I have all my stuff hooked up and I'm running all of my tests prior to wasting any resin. I have a question for y'all; when running a test print, everything seems to...
  3. Replies
    85
    Views
    67,749

    @bolsoncerrado, I've hooked up everything up and...

    @bolsoncerrado, I've hooked up everything up and am going through each page now for setup. I've also included the camera and enabled it. I can manually take a photo but it never shows on the dash.....
  4. Replies
    85
    Views
    67,749

    Hi All! I finally had a chance to start...

    Hi All!

    I finally had a chance to start playing with this. I hooked up my Pi3 and loaded Nano. (latest build 1209). Pretty simple to load! I'm still going through all of the Nano settings to get...
  5. Replies
    83
    Views
    146,927

    Sticky: Hi @acnow, I have not setup my Morpheus to run...

    Hi @acnow,

    I have not setup my Morpheus to run on Nano yet. I dont have any advice on this one. Sorry pal.
  6. Replies
    83
    Views
    146,927

    Sticky: Updated SuperVat

    After playing around with the Super-vat idea.. I decided to attempt a hybrid to test out if the liner that I am working with will work the way I hope it will.
    So I am making my own Vat liner...
  7. Are you liking running from Nano?

    Are you liking running from Nano?
  8. @bolsoncerrado, So the screen just "blanks".....

    @bolsoncerrado, So the screen just "blanks".. after a while?.. Can you elaborate a bit? .. After I get my new vat finished, the next step was Rpi3 and Nano... I also have a Rpi2.. May just go with...
  9. Replies
    83
    Views
    146,927

    Sticky: Whaaaaaa???? Can you attach vid of what it's...

    Whaaaaaa???? Can you attach vid of what it's doing?
  10. Replies
    83
    Views
    146,927

    Sticky: just a visual effect..lol.. Camera is tricky.....

    just a visual effect..lol.. Camera is tricky.. good eye tho!

    - - - Updated - - -

    I picked them (screws) up at my local Ace Hardware store. This is new bar altogether so I fitted my own.. they...
  11. Replies
    83
    Views
    146,927

    Sticky: Build plate officially completed... on to the...

    Build plate officially completed... on to the SuperVat adaptation....hmmmmmm1491
  12. Replies
    83
    Views
    146,927

    Sticky: A printer printing and replicating its own...

    A printer printing and replicating its own replacement parts... Is this where robots take over the world?..lol

    Sent from my SM-G930V using Tapatalk
  13. Replies
    83
    Views
    146,927

    Sticky: http://uploads.tapatalk-cdn.com/20160611/3cbac14db...

    http://uploads.tapatalk-cdn.com/20160611/3cbac14db1ef5d4565b27942b4b7f030.jpg

    So this is the partially completed new smaller build plate sitting inside the SuperVat. (I laugh every time I say or...
  14. Replies
    83
    Views
    146,927

    Sticky: @Sukvir, Thanks for giving credit where its due.....

    @Sukvir, Thanks for giving credit where its due.. @woale, 1,000 apologies, THANK YOU for your awesome Vat lock down.. :)

    Sukvir, on my plate mod, there is a large hollow block that the plate...
  15. Replies
    85
    Views
    67,749

    @acnow, What @woale means is that you will no...

    @acnow, What @woale means is that you will no longer have a monitor to "look at" like the screen on the laptop you currently have attached to the Morpheus. Everything you see/use for the Nano...
  16. Replies
    89
    Views
    74,576

    Something else I have resorted to when printing: ...

    Something else I have resorted to when printing:
    Anytime I make a config change (or am printing something that will take many hours), I will then adjust the Z-lift height to 40mm (which is the...
  17. Attempting a smaller single vat.. wish me luck...

    Attempting a smaller single vat.. wish me luck [emoji6]

    Sent from my SM-G930V using Tapatalk
  18. Replies
    83
    Views
    146,927

    Sticky: I've been working through a couple of design...

    I've been working through a couple of design iterations for that very reason. Seeing how I'll need to retrofit it to the existing Morpheus design, I'm making a custom frame from aluminium bars to...
  19. Replies
    89
    Views
    74,576

    It WAS a long post.. *sorry* lol Assuming you...

    It WAS a long post.. *sorry* lol

    Assuming you mean me, I haven't put together the new vat yet, its still WIP..
    Im "hoping" a smaller vat might better utilize MJ+.. I'd hate for it to go to...
  20. Replies
    83
    Views
    146,927

    Sticky: Got my Pi3, end-stops, and new vat materials...

    Got my Pi3, end-stops, and new vat materials (gonna try my hand at making a smaller vat as well.. only 1 small vat in the center instead of 2 like @sukvir's).. I got some work to do..lol

    I really...
  21. Replies
    89
    Views
    74,576

    Overdue Update! (Ramblings and Musings of an Angry Panda)

    Hello All,


    Long time, No Post!! HAHAHAHA! (I know this thread is for Successful prints, and this post goes all over the place.. so feel free to move it where you want it to go..):cool:


    I’m...
  22. Replies
    89
    Views
    74,576

    Hi golks! Angry Panda checking in.. I've been...

    Hi golks! Angry Panda checking in.. I've been extrememly busy with life but following the forum loosely. I've had some successes Ill share this weekend!

    Sent from my SM-G930V using Tapatalk
  23. Replies
    83
    Views
    146,927

    Sticky: Agreed! EXCELLENT POST!!! Thank you @sukhvir!!

    Agreed! EXCELLENT POST!!! Thank you @sukhvir!!
  24. Replies
    41
    Views
    41,511

    Got it! That makes sense!

    Got it! That makes sense!
  25. Replies
    89
    Views
    74,576

    Anxiously waiting! Lol [emoji16]

    Anxiously waiting! Lol [emoji16]
Results 1 to 25 of 89
Page 1 of 4 1 2 3 4