Search:

Type: Posts; User: TommyDee

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. The Eora or a different scanner?

    The Eora or a different scanner?
  2. It's heeeeeeeeeeere... Still in the box. Need...

    It's heeeeeeeeeeere... Still in the box. Need phone and software. Maybe I'll wait until the SW is mature enough before diving in.
  3. Replies
    299
    Views
    50,191

    Sticky: You might consider the tips a few posts back on...

    You might consider the tips a few posts back on how to downgrade firmware using the pause once the legit FW update gets started.
  4. Thread: HubCap V1

    by TommyDee
    Replies
    59
    Views
    2,123

    [ THING ] I've flattened the tabs on the stock push-nut if...

    I've flattened the tabs on the stock push-nut if they've been overworked. A common pair of pliers will do the trick. I measures the tube OD at 3.2mm where 1/8th inch is 3.18mm.
  5. Replies
    11
    Views
    2,864

    [ HOW TO ] +1 on Cosmoneer's post. A couple things too add....

    +1 on Cosmoneer's post. A couple things too add.

    1) I can swap a glass plate with magnets for a stock plate for leveling. However, there is no guarantee the thickness of what you used to apply...
  6. Thread: HubCap V1

    by TommyDee
    Replies
    59
    Views
    2,123

    [ THING ] I wonder what could cause that. I made a...

    I wonder what could cause that.

    I made a version that I suspect grew from the heat and pushed off the black bottom cover after about 10 minutes... twice!
    On the other printer I ran a different...
  7. Replies
    7
    Views
    183

    Apple ignorant here... ...

    Apple ignorant here...

    Mac...http://file.cubify.com/Download/cube-software-mac
    The app... https://itunes.apple.com/us/app/cubify/id917671806?ls=1&mt=8
    From here... ...
  8. Replies
    8
    Views
    172

    You will probably find the cheaper fan...

    You will probably find the cheaper fan under-powered. That 2.04W is a hard target to hit with generic fans. My preplacement added an extra wire for sensor feedback that can be ignored for full...
  9. Replies
    299
    Views
    50,191

    Sticky: Thanks for sharing that. I have all the parts. ...

    Thanks for sharing that. I have all the parts. Just need time with a soldering iron and some FW uploading.

    I almost pulled the trigger on the Rekindle version so making a donation to unlock the...
  10. Replies
    7
    Views
    183

    Will your IOS load the default 3D Systems app? ...

    Will your IOS load the default 3D Systems app? That's the best place to start.
    Remember that the Cube3 is a closed system to the 3DS app and the M$ app 3DBuilder.
    Mythandar created an app that...
  11. Replies
    64
    Views
    6,154

    Sticky: What's a Inf Rinse chip worth these days?

    What's a Inf Rinse chip worth these days?
  12. Replies
    7
    Views
    183

    ...and 3D Builder if you are on Windows 10

    ...and 3D Builder if you are on Windows 10
  13. Replies
    4
    Views
    161

    A thin Lithophane will print without fill if you...

    A thin Lithophane will print without fill if you limit the thickness.
    This allows the depth of the print to come through with light.
    It is the layer thickness that makes up most of the...
  14. Replies
    4
    Views
    162

    That can't be good... but it should only deal...

    That can't be good... but it should only deal with the wire management. But underneath that could be more issue.
    If this strains a wire, then yes, it could "glitch" into thinking it is a valid...
  15. Replies
    299
    Views
    50,191

    Sticky: Now I understand :) The temperature change app...

    Now I understand :)

    The temperature change app is by Mythandar. It is posted somewhere here on the forum.
    I haven't used it but I am not sure how the conversion app wouldn't work.
    Then again,...
  16. Replies
    299
    Views
    50,191

    Sticky: There are some options, such as the temperature...

    There are some options, such as the temperature changing app, that can change the .cube3 file temperature settings.
    This would allow you to use a PLA chip with ABS filament loaded.

    The premium...
  17. Replies
    4
    Views
    162

    Do you get an error message just before it stops?...

    Do you get an error message just before it stops?

    Tnn errors are associated with thermal issues at the nozzles.
    Chip disconnect errors give you 30 seconds to correct.
    A power supply disconnect...
  18. :o enjoy!

    :o enjoy!
  19. Okay, the default auto-gap is set in calibration....

    Okay, the default auto-gap is set in calibration. After it performs cal1 and set with a generous clearance, press the screen just to the right of the Cal2 label. This will initiate another...
  20. You want the auto-level to work. Without it, you...

    You want the auto-level to work. Without it, you have some unknown leveling state in the machine that you have to work with when manually leveling. Simple way to make auto-leveling work is to cover...
  21. Replies
    299
    Views
    50,191

    Sticky: I am vested in Print-R-Bot filament for general...

    I am vested in Print-R-Bot filament for general purpose. It is a little touchier about sticking to LokBuild. I back it with CubeGlue.
    Also liking the 3D Solutech for its vivid color. Most like...
  22. Replies
    299
    Views
    50,191

    Sticky: Right at this moment, you can probably beat $200...

    Right at this moment, you can probably beat $200 to your door on eBay. These deals cycle until the remaining inventory is exhausted.

    This printer is in a nutshell, the culmination of all the...
  23. Replies
    299
    Views
    50,191

    Sticky: http://www.print3dforum.com/showthread.php/1099-In...

    http://www.print3dforum.com/showthread.php/1099-Interesting-reading-(on-the-Cube3-hack)
  24. Replies
    299
    Views
    50,191

    Sticky: The "patch" doesn't deal with 0% cartridges. But...

    The "patch" doesn't deal with 0% cartridges. But there I a solution for that as well.
  25. Replies
    299
    Views
    50,191

    Sticky: vampi; can you clarify?

    vampi; can you clarify?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4