Search:

Type: Posts; User: JohnTee

Page 1 of 7 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    155
    Views
    3,561

    This obviously is not his first rodeo!! ;)

    This obviously is not his first rodeo!! ;)
  2. Replies
    155
    Views
    3,561

    Got it. That is one nice piece of work, bb! ...

    Got it. That is one nice piece of work, bb!

    Kudos to you, and to TD for all the ideas and info.

    Future tweak - could the Printer Model be a pull-down list?
    If so, then perhaps on selection...
  3. Replies
    155
    Views
    3,561

    Can I play?? Where do I find the current...

    Can I play??

    Where do I find the current version?
    Are they at the links in Post #1?
  4. Oops, nothing of interest here, move on.

    Oops, nothing of interest here, move on.
  5. Replies
    214
    Views
    39,264

    @TD My printers never connect to the Internet (I...

    @TD
    My printers never connect to the Internet (I use a standalone wifi if I want to see what it is doing or use the M$ driver), so I have never seen the message you allude to. My bad for not knowing...
  6. Replies
    214
    Views
    39,264

    Ok, here goes... This may turn out to be like...

    Ok, here goes... This may turn out to be like auto forum oil wars, or motorcycle tire wars, but we plunge in.

    Given that (a) you can easily convert one to the other with a simple firmware reload;...
  7. Replies
    5
    Views
    66

    Question: How do you grip the nozzle without...

    Question:
    How do you grip the nozzle without deforming it?

    (I'll bet you have already built a tool for this! :)
  8. Replies
    46
    Views
    4,478

    [ HOW TO ] Yes. With Recube Pro you can set % to any value,...

    Yes.
    With Recube Pro you can set % to any value, from 0 to 100.
    I always set my chips to 97%, because it's prime. :cool:
  9. Edit 8/19: Humph! As usual, you thought of...

    Edit 8/19:

    Humph!

    As usual, you thought of things that would never have occurred to me!! http://www.print3dforum.com/images/smilies/rolleyes.png

    Thanks for the insight.
    -----------------
    ...
  10. Question: Does the Cube 3 firmware do anything...

    Question: Does the Cube 3 firmware do anything differently for an ABS cartridge vs a PLA cartridge?
    Is there any reason why I can't wire a chip permanently to the contacts, and therefore not need...
  11. FWIW - A workaround for adding something before...

    FWIW - A workaround for adding something before someone else has replied to your post is to edit your post and add the new stuff after a line of dashes.

    ------------------------------
    Like this!...
  12. Replies
    7
    Views
    354

    Aha, I see. Nice! The battery case example looks...

    Aha, I see. Nice!
    The battery case example looks as if you used little rectangular holes.
    I wonder how small you could make the holes so Cube Print would still honor them?
    Could they be small...
  13. Replies
    7
    Views
    354

    @TommyDee - Could you please elaborate a little...

    @TommyDee -
    Could you please elaborate a little on "microholes"?

    Does this mean to design small diameter holes thru thin walls?
    What diameter works well?
    How closely spaced?
    Why does this...
  14. ...but you are still welcome to be here!! :)

    ...but you are still welcome to be here!!
    :)
  15. Replies
    4
    Views
    345

    Hi KH-MM, I've been drifting for a while. I...

    Hi KH-MM,
    I've been drifting for a while.
    I have a spare Cube with what I think is a motherboard problem (boots part way up, but hangs with an "0.22" code), so I've thought about trying to replace...
  16. Replies
    6
    Views
    467

    Oops - no logs. I've slept more than twice since...

    Oops - no logs. I've slept more than twice since then!
    :rolleyes:
    I kind of gave up on the idea. At least until Windows 7 support ends!
  17. Thread: Z gap

    by JohnTee
    Replies
    6
    Views
    461

    Total agreement with warming the...

    <Thumbs Up>
    Total agreement with warming the plate right before starting a print.
    A heat gun on low setting can be used, too. Keep it far enough away not to attract the magnets; your fingers...
  18. Thread: Z gap

    by JohnTee
    Replies
    6
    Views
    461

    What works for me... For PETG and ABS...

    What works for me...

    For PETG and ABS printing:
    I always use the Setup/Calibrate/Auto Gap routine, with a sheet of paper or card stock on the print bed (since i have a sloppy layer of dried glue...
  19. Replies
    428
    Views
    136,716

    Sticky: Try...

    Try
    http://cubify.s3.amazonaws.com/Printers/Cube/cube%20V1.14B.ar
  20. Replies
    46
    Views
    4,478

    [ HOW TO ] The ad looks very good - clear and complete...

    The ad looks very good - clear and complete description IMO. Very good deal!

    Oh, and my nano does have those pads - I just didn't know where to look...
  21. Replies
    46
    Views
    4,478

    [ HOW TO ] How many do you have, Tom?? :p "Basically,...

    How many do you have, Tom?? :p

    "Basically, configure a NANO as an ISP and load the current Arduino bootloader onto a properly connected NANO."

    That is above my pay grade!!

    My nano's don't...
  22. Replies
    6
    Views
    467

    No idea - maybe using some of it's UI functions?

    No idea - maybe using some of it's UI functions?
  23. Replies
    46
    Views
    4,478

    [ HOW TO ] on not getting entangled - hadn't...

    <Thumbs Up> on not getting entangled - hadn't thought about that aspect.
    Point taken on the fact someone can buy a $3 nano and make it work...BUT... that requires thinking, and figuring, and...
  24. Replies
    6
    Views
    467

    Yep - thanks for the reminder. Didn't hit that...

    Yep - thanks for the reminder. Didn't hit that roadblock yet, but I have now installed OpenGL in the form of "freeglut" & dependencies.

    The first obstacle is:
    "Cube Print cannot be installed...
  25. Replies
    6
    Views
    467

    CubePrint on Linux ???

    A quick attempt at installing CubePrint 3.04 under WINE on Linux Mint 19.1 Tessa failed, with a message about needing Internet Explorer 10 or later.

    A quick attempt at installing IE10 just failed...
Results 1 to 25 of 173
Page 1 of 7 1 2 3 4