Search:

Ditto that! Thank you for preserving these files, since 3DS abandoned them in '019...

On its way!

Maxaye, check PM.

TommyDee - that would be a brilliant mod!

Ah! There's nothing like a faulty memory chip - in my head!

Looking back at my notes, I found that the S/N is encrypted in the cfg.bin file.

BTW I have two other printers that power up...

FWIW...

I ran a diff on BuddyBu's modified file vs the version I have been using (if and when I load the Eko firmware.)

There are three two-byte differences - each just before the CR-LF of a...

I've used the same patched firmware file on the same usb flash drive on all my Ekocycle machines.

Where they get particular is if you update files on the internal SD card. Technically the (I...

Ah, thanks for the PETG tip. I'll try some on next order.

I have Polymaker Polylite red and some Chinese green PETG which works, but I have not perfected the setup yet. I use the cube glue slurry...

If 'Toolbox' means the patch to stop the filament % countdown, then yes, there is a version for Ekocycle.
The exact hex mods to the firmware are different in detail, of course, but the effect is the...

Hey Max,

FWIW I replied to your PM last night while you were working in this thread. I didn't realize then, but you are MUCH farther along here than I suspected when I replied.

I agree with the...

How goes it -- have you had a chance to try the TPU yet? (anxious followers are awaiting!)

Hooray for your engineering 'light bulbs', TD! I'm looking forward to whatever it is you are visualizing, as I have found grooving the tube to be the trickiest part of doing a B2B conversion.
...

Good deal - we'll all be standing by to see how it works for you.
What brand did you order and what vendor?

Oh, and what bowden setup are you using? TommyDee's B2B, perhaps?

Thanks!

Who has printed a TPU filament on the Cube 3, and how did it work out?

Surprisingly low price. Looks really nice.
Is it conductive?? :p:rolleyes:

------------------------
Different question for TD:
It appears that you prefer respooling the cartridges rather than...

R o t f l !!!

Good point.
Maybe they installed a tiny squirrel in there that turns the shaft with it's teeth?
If so, mine is in bad need of some dental work!

----------------
BTW, the temperatures are spot...

It gets weirder...

When i switched build plates, it began to print.
The one I was using at first was kind of rough, with nozzle dents and grooves from improper Z-gaps. I cleaned and sanded it,...

I did swap out the motherboard, as the original was broken. This is the first time I've tried to use it since the swap.
I am using the same power supply that works with the other two printers.
If I...

I did swap out the motherboard, as the original was broken. This is the first time I've tried to use it since the swap.
I am using the same power supply that works with the other two printers.
I...

Thanks, Tom.

Since there is nothing in the filament path to stop it you have two choices. Extruder clogging or filament motor driver weakness.
-- I am leaning toward motor weakness. Does...

I'm working on getting a Cube3/Ekocycle printer going. I had to replace the motherboard -- thanks to help from geofreitag -- to get it working.

Now, when I try to print, it seems that it cannot...

FWIW, I took a shot at installing CubePrint under Wine on Linux Mint a while back. As best I remember, I hit a dead end when it insisted it needed a certain version of Internet Explorer (10, I...

Brilliant!
Didn't think of that, and if I had I would've thought it wouldn't work!

Nice to be printing again, after a hiatus due to busyness.

Good suggestion.

Turns out, I had made a bad ASSumption about the encoder version buddybu included in the tools folder.
(Long story follows - skip to end if helpful...)
I copied the...

I'm now having a Windows problem with cube3-encoder on Windows 7 Pro (with September updates.)

It throws an Error Dialog =
"The application was unable to start correctly (0x000007b). Click OK to...

This obviously is not his first rodeo!! ;)