Search:

Type: Posts; User: TommyDee

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    115
    Views
    16,766

    [ HOW TO ] The commands highlighted are query commands; the...

    The commands highlighted are query commands; the 'change' commands are 8, 9, 10, & 11.

    If the chip is already cubepro, do not change it. If you change a printer type, you also need to change 'max...
  2. Replies
    115
    Views
    16,766

    [ HOW TO ] Yes, that is what I consider a command line. Not...

    Yes, that is what I consider a command line. Not sure of the current name for such things.

    Wonderful, you should be charging chips anytime.
  3. Replies
    115
    Views
    16,766

    [ HOW TO ] I think you are ahead of me in understanding the...

    I think you are ahead of me in understanding the ReCube app. Yes, you can string commands. And yes, you can use them individually.

    Have you already connected the components to program your...
  4. Replies
    115
    Views
    16,766

    [ HOW TO ] Correct, you can string commands together. To...

    Correct, you can string commands together.

    To recharge a chip to 100%; 8,100;[enter]
  5. Replies
    115
    Views
    16,766

    [ HOW TO ] Yes, this means the recube program is installed....

    Yes, this means the recube program is installed.

    You can open the Arduino Monitor Window for that port and set it to 115200 in the lower right corner of the window.
    A series of commands is...
  6. Replies
    115
    Views
    16,766

    [ HOW TO ] Please confirm your Arduino is the latest...

    Please confirm your Arduino is the latest bootloader for the 115200 baud rate specified. If it is the old bootloader, change 115200 to 57600.
  7. Replies
    115
    Views
    16,766

    [ HOW TO ] http://www.print3dforum.com/showthread.php/1892-Th...

    http://www.print3dforum.com/showthread.php/1892-The-ReCube-Wand-Help-Thread?
  8. Replies
    6
    Views
    133

    I am not familiar with Simplify3D to understand...

    I am not familiar with Simplify3D to understand the process well enough. Simplify 3D has a profile for CubePro. There is a step where you 'compile' the file using a conversion utility. A few...
  9. No idea. However, welcome to the forum.

    No idea. However, welcome to the forum.
  10. Replies
    6
    Views
    133

    Yes, they are installing the hacked version of...

    Yes, they are installing the hacked version of the firmware. It is problematic and I don't recommend it for CubePro. There have been two reports of improperly operating chamber heaters causing...
  11. Welcome to the forum. I am not familiar enough...

    Welcome to the forum. I am not familiar enough to comment so I will leave that to others.
  12. Replies
    6
    Views
    133

    You need the slicer app -...

    You need the slicer app - cubify.s3.amazonaws.com/Printers/Cubepro/cubepro_2.02.exe



    - - - - - - - - - -

    And this is the v2.02 firmware link -...
  13. Replies
    456
    Views
    193,055

    Sticky: We have all been left with little guidance. This...

    We have all been left with little guidance. This is why this small community. I do like my CubePro Duo for some things. It is the slicer that is limited. There is solutions for that. You need to...
  14. Replies
    456
    Views
    193,055

    Sticky: Let me avoid the translation Justine. I do not...

    Let me avoid the translation Justine. I do not know of a video for opening the cartridge case. It is fairly obvious once you find the latches. These are taken apart by either squeezing the case in...
  15. Replies
    456
    Views
    193,055

    Sticky: You are welcome. I do not know about tips. On...

    You are welcome. I do not know about tips. On the cartriges, cut along the label; then depress the small latches along the periphery of the case. Do not loose the chip. Also be very careful with...
  16. Replies
    456
    Views
    193,055

    Sticky: https://www.ebay.com/itm/3D-Systems-Cube-3-Cube-X-...

    https://www.ebay.com/itm/3D-Systems-Cube-3-Cube-X-Cube-Pro-Ekocycle-3D-Filament-Cartridge-Refill-Resetter/153900451809?

    These work. I design this with Tomuro code. You can also contact member...
  17. Welcome to the forum xapk. That is odd as...

    Welcome to the forum xapk. That is odd as slicers are where things would choke. Can you preview the sliced file? This is definitely a process that needs to be evaluated at every step. I have...
  18. This will get you started......

    This will get you started...
    http://www.print3dforum.com/showthread.php/3024-3DS-Cube-File-Links
  19. I have very little trouble with 3rd party PLA. ...

    I have very little trouble with 3rd party PLA. But I don't use exotic PLA like GITD or harder filaments. The Cubes have a fixed filament gap and therefore harder filaments are problematic. Tuning...
  20. Thread: Marlin Help

    by TommyDee
    Replies
    5
    Views
    209

    Can the driver take the torque of both steppers? ...

    Can the driver take the torque of both steppers? It should equal out as the load will be halved with margin for extra resistance.

    Typically slaving is done through the f/w drivers and encoders...
  21. Thread: Marlin Help

    by TommyDee
    Replies
    5
    Views
    209

    In professional dual-drive systems, the second...

    In professional dual-drive systems, the second motor is slaved to the first. Driving into end-stops keeps them balanced.
  22. Replies
    340
    Views
    26,976

    I have never regretted buying a canned system in...

    I have never regretted buying a canned system in the Cube3. It did exactly what it was suppose to do - send it a design and it prints it. That is the theory anyway. Well, 3 years and a few gadgets...
  23. Replies
    340
    Views
    26,976

    Today I decided to try a 'pause' in the print...

    Today I decided to try a 'pause' in the print using the editor. I've been printing a lot of PETG lately and I had a terrible time with dual extrusion. Filament kept bleeding from the small snags.
    ...
  24. Replies
    1
    Views
    133

    or a connection problem

    or a connection problem
  25. Replies
    3
    Views
    220

    That is probably a transorb. An over-voltage...

    That is probably a transorb. An over-voltage shunt device. The UL says its a safety rated device.

    Even better - inrush current limiting device i.e. 10 ohm resistor...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4