Search:

Type: Posts; User: PRIma

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    16
    Views
    43,606

    Hi, I have printed in PLA and the heat bed was...

    Hi,
    I have printed in PLA and the heat bed was turned off...very strong adhesion indeed!
    Regarding the 0.1 gap i used a sheet of paper which is approx. 0.1mm thick (measured by caliper) - if the...
  2. Replies
    16
    Views
    43,606

    first time printing with LokBuild a few days ago...

    first time printing with LokBuild
    a few days ago I received my LokBuild and here is some comment of my first trial:
    1.mounting LokBuild
    goes very easy and without any bubbles at all. If necessary...
  3. Replies
    16
    Views
    43,606

    Just pledged for one of those as i am tired of...

    Just pledged for one of those as i am tired of using Kapton Tape ...:rolleyes:
  4. Replies
    5
    Views
    10,568

    3D printed Folding Knife

    I found some interesting design of a Folder on thingiverse which was original created by JeremyBP
    www.thingiverse.com/thing:90158

    I re-designed it into a thumb-stud model and as well changed the...
  5. Replies
    4
    Views
    4,885

    yes-just recognized the error message when try to...

    yes-just recognized the error message when try to click on the link above....
    I have now uploaded both Extruder Fan which was originally send with the printer on thingiverse...
  6. Replies
    4
    Views
    4,885

    Fan Duct original STL File

    see attachment :)
  7. Replies
    2
    Views
    9,237

    "Braq" jointed dragon

    it says it will be a challenge for your printer...came out great!
    1184
    1185
    11861187
    printed in PolyPlus PLA/ 0.2mm Layer
    Link: http://www.thingiverse.com/thing:854575
  8. men in black mini gun? -any aliens around your...

    men in black mini gun? -any aliens around your place? LOL;)
  9. Replies
    43
    Views
    26,561

    i am not an electrican expert but i think it will...

    i am not an electrican expert but i think it will increase the voltage (12V) in general and not only the heater (heat-bed)
  10. Replies
    43
    Views
    26,561

    it was 11.8V at my first measure (should be 12V...

    it was 11.8V at my first measure (should be 12V for sure lol) currently i`m running with 13-14V
    important: increase the voltage just a little bit!
  11. Replies
    43
    Views
    26,561

    I had similar problems with heating up the print...

    I had similar problems with heating up the print bed...increased very slowly and could not get over 90degree.
    Ethan told me following step:
    1.open the bottom cover of the printer
    2. at the power...
  12. Replies
    21
    Views
    15,908

    Not sure but the 2nd screenshot shows that you...

    Not sure but the 2nd screenshot shows that you set an Nozzle diameter of 4mm instead of 0.4mm?
  13. Please check the rods diameter as well (with...

    Please check the rods diameter as well (with micrometer if available)...one of my Y-axis rod had a different diameter (smaller about 0.015mm) than the other one and this makes additional wobbling to...
  14. Replies
    19
    Views
    12,361

    Finally got my new sparepart (heat breaks with...

    Finally got my new sparepart (heat breaks with PTFE tube) and assembled everything back together.Printing now smooth again like a baby`s bottom ;).
    From now, i will more take care about removing the...
  15. Replies
    19
    Views
    12,361

    thanks for the feedback-by pulling it back i...

    thanks for the feedback-by pulling it back i meant retract by the buttons in repetier.My temperature is around 180degree and before i did not had any issues with that step.@BobenhamHotspur for...
  16. Replies
    19
    Views
    12,361

    Hello again, I keep using this thread because i...

    Hello again,
    I keep using this thread because i think my new problem has probably some relation to my previous one.
    when i try to remove the filament which i used for printing the filament get ...
  17. Replies
    19
    Views
    12,361

    Good News-my printer works again after exchange...

    Good News-my printer works again after exchange the extruder thermistor!
    all functions checked and i`m printing now:p
  18. Replies
    19
    Views
    12,361

    I was able to remove the jam by simply drilling...

    I was able to remove the jam by simply drilling with an 2mm drill trough the tube and the ptfe tube remained in place and seems undamaged which is nice:)- one problem solved.

    Regarding the...
  19. Replies
    19
    Views
    12,361

    I disconnected the extruder thermistor at board...

    I disconnected the extruder thermistor at board side and tested if i can at least heat up the bed - temp does not change.

    Regading remove the ptfe tube: some unmelted filament still stuck inside...
  20. Replies
    19
    Views
    12,361

    SAO, thanks for the info`s. The thermistor came...

    SAO, thanks for the info`s. The thermistor came out with the head (which is covered in glass). The wire itself looks ok.
    If the whole hotend thermistor is dead then i`m just wondering why i have now...
  21. Replies
    19
    Views
    12,361

    chain reaction of problems started

    Hi,
    I was lucky so far with my RL printer because until now i did not had any big issues.But now... i am facing some problems and maybe some forum members can give me any advice to solve the...
  22. Thread: X Wing Slider

    by PRIma
    Replies
    82
    Views
    56,120

    @BobenhamHotspur Looks interesting so far.. as i...

    @BobenhamHotspur
    Looks interesting so far.. as i am located in Japan the shipment costs would be probably higher than ordering the X-wing Slider upgrade from Rapide:(
    additional my X-wing Slider...
  23. Replies
    25
    Views
    16,302

    check out this link: http://uk.misumi-ec.com/ ...

    check out this link:
    http://uk.misumi-ec.com/ (other countrys than UK available too)
    this company has a wide range of components (rods, sliders, bearings ...huge amount!) which can be ordered...
  24. It`s done in PLA. I used PolyPlus Filament "true...

    It`s done in PLA. I used PolyPlus Filament "true white" von Polymakr which i wanted to test. Surface looks a little rough on this print with my used settings- sure can be optimized :D
  25. # 3 D Benchy / 3D Model specifically designed for testing & benchmarking 3D Printer

    Hello,
    This is a good & simple model to check your printer`s accuracy. go to the homepage www.3dbenchy.com where you find the link to download the free .stl file.

    884


    885


    here is a...
Results 1 to 25 of 35
Page 1 of 2 1 2