Search:

Type: Posts; User: TommyDee

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    7
    Views
    47

    The least of the things you want to know about is...

    The least of the things you want to know about is the chip re-setter once you get to printing proper. https://www.ebay.com/itm/393710704973?hash=item5baafc994d:g:3v8AAOSwNslhmJe4


    There is also...
  2. Replies
    7
    Views
    47

    You might have a few things to learn. Enjoy the...

    You might have a few things to learn. Enjoy the adventure :)
  3. Replies
    7
    Views
    47

    Considering these are closed systems, since we...

    Considering these are closed systems, since we have little control over the print parameters, this is 'proper' behavior. However, we can hunt down thes elines in the print file and eliminate them. ...
  4. Replies
    4
    Views
    77

    Use it and enjoy it. I have a CubePro in a...

    Use it and enjoy it. I have a CubePro in a similar situation. Too hard to ship.
  5. Replies
    4
    Views
    77

    Not sure if the value is greater than the sum of...

    Not sure if the value is greater than the sum of the parts.
  6. Replies
    28
    Views
    166,267

    Sticky: I can still do this nicko.

    I can still do this nicko.
  7. Replies
    1
    Views
    120

    Too hot. PLA likes around 80 degrees in the room...

    Too hot. PLA likes around 80 degrees in the room and no heating of the bed. Make sure the nozzle isn't radiating excess heat at the print.
  8. Replies
    326
    Views
    546,752

    Sticky: You might consider a local STEM program in a...

    You might consider a local STEM program in a local school. Although this is a great offer, and I would take you up on it if it came to $50 or less, a local program for kids and young adults may...
  9. You hear the ticks. It is a process. But you...

    You hear the ticks. It is a process. But you can test it with a border print to see if the filament is equally wide all around as a test.

    I've lain a white sheet of paper on the surface to fool...
  10. Have a look here -...

    Have a look here - http://www.print3dforum.com/showthread.php/1165-Z-ticks?highlight=z-ticks

    I don't ever auto-level.
  11. Replies
    3
    Views
    405

    Some people here have parted out machines and...

    Some people here have parted out machines and offered parts. Sometimes they show up on Ebay. It is hard to find parts. Feel free to post for parts in CubePro for-sale/trade section. Here is a...
  12. Replies
    3
    Views
    405

    This is likely a sensor failure on the motor...

    This is likely a sensor failure on the motor controller board. The system monitors the black and white 'flags' on the filament drive wheels. If that is not getting processed or something is wrong...
  13. Replies
    16
    Views
    16,134

    It is probably a MOV on the heater control...

    It is probably a MOV on the heater control module. Seen that picture before. But the factory 2.02 upgrade was fine, I still run it. I honestly think that settings go out of bounds for the heater...
  14. Replies
    34
    Views
    30,507

    Sticky: You can write a custom g-code (*.cubepro) file...

    You can write a custom g-code (*.cubepro) file that only initiates the heater.
  15. Thread: Wood Filament

    by TommyDee
    Replies
    3
    Views
    598

    Connect with Tamir1an

    Connect with Tamir1an
  16. Aha, now I understand what you are after. I have...

    Aha, now I understand what you are after. I have not captured that print file. Hopefully someone else here has this in their archives and is willing to post it.

    If you want to, you could try to...
  17. All you can do is request the files. The user...

    All you can do is request the files. The user doesn't participate here anymore.

    You are also welcome to check some of my alternatives on thingiverse - https://www.thingiverse.com/qube3bot/designs...
  18. Replies
    8
    Views
    5,668

    Something to do with entering a code?

    Something to do with entering a code?
  19. Replies
    26
    Views
    7,430

    More gap. To little gap presents to the machine...

    More gap. To little gap presents to the machine like a clog.
  20. Replies
    26
    Views
    7,430

    Not from the pictures. You could try unplugging...

    Not from the pictures. You could try unplugging them and see if it boots after that.
  21. Replies
    26
    Views
    7,430

    Looking good so far. I use CubeGlue on my...

    Looking good so far.

    I use CubeGlue on my LokBuild for great service. However, LokBuild does work well without glue with several materials.

    Glue on LokBuild can be recharged by simply misting...
  22. Replies
    9
    Views
    1,617

    The only posts we've seen about failed heaters...

    The only posts we've seen about failed heaters was after the hack so I bet it is the culprit. Not sure how it would do that though. Somewhere in the firmware is where the chamber temperature is...
  23. Replies
    9
    Views
    1,617

    The fan on the heater is on all the time but the...

    The fan on the heater is on all the time but the heater has a thermal fuse internally to stop heating. Technically, it should be hardwired to the AC input.

    I am not sure anyone has investigated...
  24. Replies
    9
    Views
    1,617

    There should be a version 2.02. Yes, .ar is the...

    There should be a version 2.02. Yes, .ar is the right extension and cubepro is the appropriate prefix.
  25. Replies
    9
    Views
    1,617

    We have the Cubify repository stored among us. ...

    We have the Cubify repository stored among us.

    http://www.print3dforum.com/showthread.php/3024-3DS-Cube-File-Links
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4