Search:

Type: Posts; User: bolsoncerrado

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    2
    Views
    48

    Price is not only the plastic implied in your...

    Price is not only the plastic implied in your project, which, btw, looking at your sizes, it can easily be way more than "10 bucks"...

    You also need to take into account FDM takes HOURS, and for...
  2. First off you need to clean everything of molten...

    First off you need to clean everything of molten plastic. Heat up to mild temp 150 or so and use a metal brush to clean up the mess as much as possible. Use also pliers and even metal rod (small...
  3. Replies
    4
    Views
    163

    Did you try contacting them directly first? Can...

    Did you try contacting them directly first?
    Can you take a picture of the LCD to see the exact message?
    Also can you take a picture of the extruder assembly to see any damage on the head?

    Thanks.
  4. Replies
    4
    Views
    163

    Broken thermistor wire maybe? Where did you buy...

    Broken thermistor wire maybe? Where did you buy it?
  5. Yes, it does seem your thermistor cables are...

    Yes, it does seem your thermistor cables are bad/cut. YOu should ask for a replacement if under warranty.
  6. But whats the exact message on the display? ...

    But whats the exact message on the display?

    Thermal Runaway?

    May be the wire is internally "cut" and it breaks the connection on certain positions only.... (when Z is low enough)
  7. Replies
    5
    Views
    209

    It could also be something inside the power...

    It could also be something inside the power supply... I'dn't leave it quite unattended...
  8. Replies
    5
    Views
    209

    Might be a motor driver overloaded or going wrong...

    Might be a motor driver overloaded or going wrong hmmm.... not that easy to solve. Where did you get your printer?
  9. You may want to put the belt tensioner upside...

    You may want to put the belt tensioner upside down and retry?
  10. At this stage these printers would be better with...

    At this stage these printers would be better with latest Marlin firmware where you can even customize your own boot logo....
  11. The laser modules are for 3D Printers, not...

    The laser modules are for 3D Printers, not "Laser/Inkjet" printers.
  12. Replies
    4
    Views
    767

    There was a guy in the FB group trading one of...

    There was a guy in the FB group trading one of these similar printers (perhaps v2?) for a Cube3 I think....
  13. Replies
    4
    Views
    767

    U want to keep printing small u mean?

    U want to keep printing small u mean?
  14. Replies
    164
    Views
    24,931

    Yeah cold pulls are as ancient as 3d printing...

    Yeah cold pulls are as ancient as 3d printing itself hehe
  15. Meanwhile, in the Scavenging Dept. ....

    https://i.imgur.com/JlK0o5C.jpg

    https://i.imgur.com/D0TbGO8.jpg

    :cool:
  16. Replies
    172
    Views
    23,353

    Lol

    Lol
  17. Replies
    35
    Views
    3,559

    I fear leather gets deformed too easily... after...

    I fear leather gets deformed too easily... after a few wipes that is.
  18. Replies
    35
    Views
    3,559

    Then full power might not be the answer ha!

    Then full power might not be the answer ha!
  19. Replies
    3
    Views
    456

    https://www.instructables.com/id/Non-manifolds-You...

    https://www.instructables.com/id/Non-manifolds-Your-Worst-3D-Printing-Nightmare/
  20. Replies
    35
    Views
    3,559

    Big mess as of flames? lol

    Big mess as of flames? lol
  21. Replies
    4
    Views
    346

    Yikes! Perhaps with some supports, indeed...

    Yikes! Perhaps with some supports, indeed...
  22. Replies
    35
    Views
    3,559

    Hey thanks for sharing! ;)

    Hey thanks for sharing! ;)
  23. Replies
    4
    Views
    346

    Man what a bible are you builing :D

    Man what a bible are you builing :D
  24. Replies
    3
    Views
    456

    Is the object you try to print manifold?

    Is the object you try to print manifold?
  25. Replies
    2
    Views
    380

    Nice layer deposition :)

    Nice layer deposition :)
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4