Search:

Type: Posts; User: clayton

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Thread: Print quality

    by clayton
    Replies
    18
    Views
    6,297

    Set your minimum layer time - I had this problem...

    Set your minimum layer time - I had this problem before with small layers - moving too fast without enough time to cool makes jello out of PLA.

    For slicr:...
  2. Replies
    3
    Views
    687

    Hi Joao - thanks for the message - I'm aware of...

    Hi Joao - thanks for the message - I'm aware of where to get the firmware - just lazy - trying to see if anyone else had already done it to save the config.

    Anyone have it already done - new...
  3. Replies
    3
    Views
    687

    Anyone have firmware for two extruders?

    Hi All,

    It's been quite a while! My RL is still moving, with a fair bit of maintenance, but I have finally put two separate E3D extruders on and I was hoping someone had done the firmware for it. ...
  4. Replies
    22
    Views
    11,623

    Let me know how to pay - and I can send it to...

    Let me know how to pay - and I can send it to you...
  5. Replies
    22
    Views
    11,623

    I always forget you're in Spain... it's not end...

    I always forget you're in Spain... it's not end of day for us yet here in Canada!

    Thanks for that, I'll take 10 f you can spare them...
  6. Replies
    22
    Views
    11,623

    Hi Bolson, I tried for the form and it's not...

    Hi Bolson, I tried for the form and it's not working -I'd like 10 8mm bearings!

    Cheers,

    Clayton
  7. Replies
    22
    Views
    11,623

    Hi All, Just caught this in time, I'd like two...

    Hi All,

    Just caught this in time, I'd like two sets for the standard RL200 - Do they just fit into the current bearing holders? How many do I need?

    Thanks!

    Clayton
  8. Replies
    107
    Views
    41,371

    Thanks Fixx - I had gotten that far and it...

    Thanks Fixx - I had gotten that far and it doesn't seem to be working for me - I'll recheck the firmware and get back!
  9. Replies
    31
    Views
    13,902

    Justin, that's super cool - keep with the pics!...

    Justin, that's super cool - keep with the pics! Stretch the Y while you're at it!
  10. Replies
    107
    Views
    41,371

    Yes, there is one thermistor, but I want the 3...

    Yes, there is one thermistor, but I want the 3 "virtual" extruders to all read off tool 0 for temp.

    Right now I have:

    Tool 0 (extruder 1)
    Tool 1 (extruder 2)
    Tool 2 (extruder 3)

    Only...
  11. Replies
    107
    Views
    41,371

    Anyone know how to route the temp from the...

    Anyone know how to route the temp from the thermistor to show for all three extruders in the firmware? I've got tool zero showing temp, but the others don't seem to...

    Thanks!
  12. Replies
    107
    Views
    41,371

    WOW Milstream - that is a great looking bunch of...

    WOW Milstream - that is a great looking bunch of mods there. Definitely up some more pix.

    Thanks!

    Clayton
  13. Replies
    107
    Views
    41,371

    I actually did an old-school job and took a piece...

    I actually did an old-school job and took a piece of aluminum, bent it roughly into shape a drilled a few holes in it. I did design a bracket for it as well, but was unable to print it, as I had...
  14. Replies
    107
    Views
    41,371

    Hi Fixx, I actually am already well past that...

    Hi Fixx,

    I actually am already well past that - I ordered the Z splitter cable on ebay and it worked with a little shaping of the plug.

    First I didn't have one of the heatsinks tightened down...
  15. Replies
    107
    Views
    41,371

    HI, I've got the diamond head mounted and have...

    HI,

    I've got the diamond head mounted and have had a few test prints. Just working with one colour so far. Having a little problem with te firmware, but making some edits - has anyone else gotten...
  16. Replies
    107
    Views
    41,371

    Did anyone get the Dianon hotend mounted yet? ANy...

    Did anyone get the Dianon hotend mounted yet? ANy luck?
  17. Replies
    7
    Views
    3,866

    So, can I use just a piece from the filament...

    So, can I use just a piece from the filament guide line? Is that PFTE?

    Thanks!

    Clayton
  18. Replies
    7
    Views
    3,866

    Replacement PFTE Source, Specs?

    Hi All,

    Has been a while! I finally burned the teflon insert in my hotend out, printing Nylon (badly).

    While it's not urgent because I'm about to fit my Diamond nozzle, does anyone have a link...
  19. Replies
    13
    Views
    9,635

    I can get it to work with either currently...

    I can get it to work with either currently...
  20. Replies
    13
    Views
    9,635

    I've tried the drv8825 and a4988. Played with the...

    I've tried the drv8825 and a4988. Played with the voltage pots on both and still getting the resonance in the stepper.
  21. Replies
    13
    Views
    9,635

    I am having a problem with the stepper motor...

    I am having a problem with the stepper motor ringing currently - so I'm losing torque and it's making quite a bit of noise. I'm not sure if it is the zum board that I soldered myself or not!
  22. HI All, Just got my scanner together - the...

    HI All,

    Just got my scanner together - the lasers work, the camera is good - connects to my MAC via Parallels and Windows 10.

    A question:

    I'm using a DRV8825 stepper motor - instead of the...
  23. Are these the oillite bearings? Did they fit in...

    Are these the oillite bearings? Did they fit in the blocks? What size? Where did you get them?
  24. I found that mine were loose as well when I...

    I found that mine were loose as well when I changed my bed to the 200x300.

    worse though, the y rods were bent. When I rotated the y rods the bed would go up and down. Much better prints with the...
  25. No real links - just trying it out - practically...

    No real links - just trying it out - practically have to use a razor to get the ABS part off, and a few hours of printing with 100% infill has not produced any warping.
Results 1 to 25 of 133
Page 1 of 6 1 2 3 4